Difficulty

Difficult

Steps

10

Time Required

                          40 - 50 minutes

Sections

1

  • Screen
  • 10 steps

Flags

0

  • BackHP Pavilion 13-P110NR

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Screen
  • Remove the back of the laptop screen using a black nylon spudger.

Remove the back of the laptop screen using a black nylon spudger.

1024

Step 2

  • Detach the wires from the green circuit boards located at the bottom.
  • Remove three 3.0 mm #00 Philips screws from the circuit board on the left.
  • Remove two 4.0 mm #00 Philips screws from the small circuit board on the right.

Detach the wires from the green circuit boards located at the bottom.

Remove three 3.0 mm #00 Philips screws from the circuit board on the left.

Remove two 4.0 mm #00 Philips screws from the small circuit board on the right.

Step 3

  • Detach the wires located just above the bigger green circuit board.

Detach the wires located just above the bigger green circuit board.

Step 4

  • Remove six 4.0 mm Philips #00 screws from the outside of the frame.
  • Remove five 3.0 mm Philips #00 screws from the outside of the frame.
  • Remove the one 3.0 mm Philips #00 screw hidden under the circuit board.

Remove six 4.0 mm Philips #00 screws from the outside of the frame.

Remove five 3.0 mm Philips #00 screws from the outside of the frame.

Remove the one 3.0 mm Philips #00 screw hidden under the circuit board.

Step 5

  • Remove the band that is attached to the circuit board, located on the right side.

Remove the band that is attached to the circuit board, located on the right side.

Step 6

  • Lift the frame and attached hardware from two corners of the frame.
  • Remove the frame from the device.

Lift the frame and attached hardware from two corners of the frame.

Remove the frame from the device.

Step 7

  • Remove the tape located at the top of the frame.
  • Remove the bands from underneath the tape.

Remove the tape located at the top of the frame.

Remove the bands from underneath the tape.

Step 8

  • Use the spudger to lift the case, which is attached at four spots by pegs.
  • Remove the metal cover and layers of film.

Use the spudger to lift the case, which is attached at four spots by pegs.

Remove the metal cover and layers of film.

Step 9

  • Use the spudger to gently lift up the screen.
  • There are two layers, go under the bottom layer.

Use the spudger to gently lift up the screen.

There are two layers, go under the bottom layer.

Step 10

  • After you get some space at the top of the screen, proceed by using a thin board to gently remove the screen from the frame.

After you get some space at the top of the screen, proceed by using a thin board to gently remove the screen from the frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Matthew "Cole" Corson

Member since: 01/18/2018

718 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Eastern Washington University, Team S2-G5, Munoz Winter 2018                        

                                                  Member of Eastern Washington University, Team S2-G5, Munoz Winter 2018 



                    EWU-MUNOZ-W18S2G5                     


                                            4 Members                     


                                            5 Guides authored