Difficulty
Moderate
Steps
9
Time Required
20 - 40 minutes
Sections
2
- Battery
- 4 steps
- Screen
- 5 steps
Flags
0
BackHP Omen 15-ax243dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- The rear panel is secured by 10 screws. Using a #00 Phillips Screwdriver, remove the ten 1.2 mm screws.
- The screwdriver should be inserted at the same angle as the screws.
- Be sure to keep track of the screws and where they came from. Some only fit in to one spot.
The rear panel is secured by 10 screws. Using a #00 Phillips Screwdriver, remove the ten 1.2 mm screws.
The screwdriver should be inserted at the same angle as the screws.
Be sure to keep track of the screws and where they came from. Some only fit in to one spot.
1024
Step 2
- Insert a plastic opening tool between the rear panel and the top case. Pry the opening tool upwards to separate the top case from the bottom case.
- Slide the opening tool along the case perimeter to loosen the bottom case.
- Gently pull the bottom case away from the laptop.
Insert a plastic opening tool between the rear panel and the top case. Pry the opening tool upwards to separate the top case from the bottom case.
Slide the opening tool along the case perimeter to loosen the bottom case.
Gently pull the bottom case away from the laptop.
Step 3
- Remove the four 1.2 mm Phillips #00 screws around the battery.
Remove the four 1.2 mm Phillips #00 screws around the battery.
Step 4
- Pull the battery cable out from its motherboard socket.
- Pull parallel to the motherboard, not straight up.
- Remove the battery.
- Disconnect the power cord from the battery and transfer it to your replacement battery.
Pull the battery cable out from its motherboard socket.
Pull parallel to the motherboard, not straight up.
Remove the battery.
Disconnect the power cord from the battery and transfer it to your replacement battery.
Step 5
Screen
- Unscrew the six 1.2 mm screws connecting the screen to the body using the #00 Phillips screwdriver head.
- Be cautious of where the screws come out from, some will only fit in the same location.
Unscrew the six 1.2 mm screws connecting the screen to the body using the #00 Phillips screwdriver head.
Be cautious of where the screws come out from, some will only fit in the same location.
Step 6
- Remove the tape holding the wires down
- Disconnect the wires from the wifi chip
- When removing the wires from the wifi chip, be careful to not damage the connectors.
Remove the tape holding the wires down
Disconnect the wires from the wifi chip
When removing the wires from the wifi chip, be careful to not damage the connectors.
Step 7
- Flip the switch up that holds the screen cable in place
- Lift up and pull back the cable from the insert
Flip the switch up that holds the screen cable in place
Lift up and pull back the cable from the insert
Step 8
- Lift the base of the device up to separate the hinges from the body of the device
Lift the base of the device up to separate the hinges from the body of the device
Step 9
- Slide the base of the device out from under the hinges
- The screen can now be replaced
Slide the base of the device out from under the hinges
The screen can now be replaced
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
vangnam
Member since: 10/19/2017
592 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
UMass Dartmouth, Team S6-G7, Rockett Fall 2017
Member of UMass Dartmouth, Team S6-G7, Rockett Fall 2017
UMASSD-ROCKETT-F17S6G7
3 Members
7 Guides authored
