Difficulty
Difficult
Steps
10
Time Required
35 minutes
Sections
2
- Motherboard
- 8 steps
- Battery
- 2 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackHP Officejet Pro 8600 Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Turn the printer so the back is facing you.
- Put the printer in a vertical position by lifting its right side.
Turn the printer so the back is facing you.
Put the printer in a vertical position by lifting its right side.
1024
Step 2
- Remove the two 12mm T10 Torx screws on the top edge of the printer.
Remove the two 12mm T10 Torx screws on the top edge of the printer.
Step 3
- Rotate the printer clockwise so the bottom of the printer is facing you.
Rotate the printer clockwise so the bottom of the printer is facing you.
Step 4
- Insert the plastic opening tool underneath the slot on the right that aligns with the edge of the back panel.
- Insert a second plastic opening tool in the notch lining up with the crease in the back panel.
- This step requires applying a significant amount of force on the left notch. Don’t be alarmed if you hear popping noises.
Insert the plastic opening tool underneath the slot on the right that aligns with the edge of the back panel.
Insert a second plastic opening tool in the notch lining up with the crease in the back panel.
This step requires applying a significant amount of force on the left notch. Don’t be alarmed if you hear popping noises.
Step 5
- Remove the side panel from the printer by lifting upwards toward you.
- For reassembly, slide the side panel from left to right into place.
Remove the side panel from the printer by lifting upwards toward you.
For reassembly, slide the side panel from left to right into place.
Step 6
- Remove the four 6.5 mm T10 Torx screws from the motherboard.
Remove the four 6.5 mm T10 Torx screws from the motherboard.
Step 7
- Remove the black brace from the right side of the motherboard, located near the black ribbon cable.
Remove the black brace from the right side of the motherboard, located near the black ribbon cable.
Step 8
- Remove the cables connected to the top of the motherboard by gently pulling them out of their ports.
- Remove the cables connected to the edge of the motherboard by gently pulling them out of their ports.
- Remove the cables connected to the underside of the motherboard by gently pulling them out of their ports.
Remove the cables connected to the top of the motherboard by gently pulling them out of their ports.
Remove the cables connected to the edge of the motherboard by gently pulling them out of their ports.
Remove the cables connected to the underside of the motherboard by gently pulling them out of their ports.
Step 9
Battery
- Turn the motherboard over so the back is facing upward.
- Use the plastic opening tool to pry the battery out of place.
Turn the motherboard over so the back is facing upward.
Use the plastic opening tool to pry the battery out of place.
Step 10
- Remove the battery by grabbing its edges, lifting upward, and sliding sideways.
Remove the battery by grabbing its edges, lifting upward, and sliding sideways.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 2 other contributors
Mackinnon Buck
Member since: 04/18/2018
1,158 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team S16-G4, Livingston Spring 2018
Member of Cal Poly, Team S16-G4, Livingston Spring 2018
CPSU-LIVINGSTON-S18S16G4
4 Members
5 Guides authored