Difficulty

Moderate

Steps

8

Time Required

                          15 - 20 minutes

Sections

2

  • Rear Plastic Panel
  • 6 steps
  • Speaker
  • 2 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHP Officejet J3680

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Unplug the Device
  • Remove the plug from the outlet and from the back of the device
  • Remove the USB Cable from your computer and from the back of the device.

Remove the plug from the outlet and from the back of the device

Remove the USB Cable from your computer and from the back of the device.

1024

Step 2

              Remove Screws From Under the Control Panel
  • Using your Torx T10 screwdriver, remove the screws indicated in the picture. Screws are 13mm in length.

Using your Torx T10 screwdriver, remove the screws indicated in the picture. Screws are 13mm in length.

Step 3

              Remove Screws Underneath the Ink Cartridge Cover
  • Using your Torx T10 screwdriver, remove the screws indicated in the picture. Screws are 13mm in length

Using your Torx T10 screwdriver, remove the screws indicated in the picture. Screws are 13mm in length

Step 4

              Remove Screws from Underneath the Phone Panel
  • In step 2, you removed the screw from the blue indicated area.
  • Gently pop off the black cover that the phone rests on. Underneath this cover, you will find two more screws.
  • Using your Torx T10 screwdriver, remove the screws indicated in the picture. Screws are 13mm in length

In step 2, you removed the screw from the blue indicated area.

Gently pop off the black cover that the phone rests on. Underneath this cover, you will find two more screws.

Step 5

              Remove the Screws from the Rear of Device

Step 6

              Remove Rear Plastic Panel
  • Once the rear plastic panel has been removed, you are ready to replace and repair the necessary parts.

Once the rear plastic panel has been removed, you are ready to replace and repair the necessary parts.

Step 7

              Unscrew the speaker
  • Using your Torx t10 screwdriver, remove the screw located on the right side of the speaker as shown in the figure on the left. The screw is 13mm in length.

Using your Torx t10 screwdriver, remove the screw located on the right side of the speaker as shown in the figure on the left. The screw is 13mm in length.

Step 8

              Detatch the speaker
  • Follow the wires, connected to the speaker, to the green mother board.
  • Then detach the white plastic piece connected to the wires, shown on the left, by gently pulling it out from the motherboard.

Follow the wires, connected to the speaker, to the green mother board.

Then detach the white plastic piece connected to the wires, shown on the left, by gently pulling it out from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Marisa

Member since: 10/22/2014

206 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       UMass Dartmouth, Team 1-1, Duarte Fall 2014                        

                                                  Member of UMass Dartmouth, Team 1-1, Duarte Fall 2014 



                    UMASSD-DUARTE-F14S1G1                     


                                            4 Members                     


                                            6 Guides authored