Difficulty

Easy

Steps

8

Time Required

                          5 - 10 minutes

Sections

1

  • WWAN Card
  • 8 steps

Flags

0

  • BackHP Mini 210 Netbook

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

WWAN connectivity allows a user with a netbook and a WWAN card to surf the web, check email, or connect to a virtual private network (VPN) from anywhere within the regional boundaries of cellular service.

The WWAN card in the HP Mini 210 uses a Mini PCIe interface, which is the standard on recent laptops. Please ensure you install an official HP verified WWAN card to prevent running into errors.

What you need

Step 1

              WWAN Card
  • Turn off and unplug the netbook before replacing the battery.
  • Hold the netbook top-side down with the lid closed.
  • Slide the plastic battery release latches towards the lock symbols.
  • The left tab unlocks completely, but you will need to hold the right tab towards the lock symbol as you remove the battery.

Turn off and unplug the netbook before replacing the battery.

Hold the netbook top-side down with the lid closed.

Slide the plastic battery release latches towards the lock symbols.

The left tab unlocks completely, but you will need to hold the right tab towards the lock symbol as you remove the battery.

1024

Step 2

  • Slide the battery out from the netbook.

Slide the battery out from the netbook.

Step 3

  • Turn the netbook to view its edge.
  • Press both orange eject buttons simultaneously, and use a spudger to pry off the back case.

Turn the netbook to view its edge.

Press both orange eject buttons simultaneously, and use a spudger to pry off the back case.

Step 4

  • Use the spudger to pry off the back case by the edge near the battery compartment, and work your way to the sides. The case will then pivot along the front edge.

Use the spudger to pry off the back case by the edge near the battery compartment, and work your way to the sides. The case will then pivot along the front edge.

Step 5

  • Pull the back case off from the front edge.

Pull the back case off from the front edge.

Step 6

  • Disconnect the two gold antenna cables from the WWAN card using a plastic opening tool.

Disconnect the two gold antenna cables from the WWAN card using a plastic opening tool.

Step 7

  • Use a Phillips #00 screwdriver to remove the two Phillips 2.0 and 3.0 mm screws that secure the WWAN to the system board.

Use a Phillips #00 screwdriver to remove the two Phillips 2.0 and 3.0 mm screws that secure the WWAN to the system board.

Step 8

  • Remove the WWAN card by pulling the WWAN card out at an angle.

Remove the WWAN card by pulling the WWAN card out at an angle.

Install the new WWAN card and then to reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 12 other contributors 


                    Heather Freed

Member since: 10/06/2012

690 Reputation

                                      8 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 9-17, Amido Fall 2012                        

                                                  Member of Cal Poly, Team 9-17, Amido Fall 2012 



                    CPSU-AMIDO-F12S9G17                     


                                            3 Members                     


                                            8 Guides authored

rioarayana - Dec 2, 2016

Reply

apakah benda tersebut ada dalam paket penjualan, atau dijual terpisah?