Hp Mini 1000 Pram Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
2 steps
Keyboard
4 steps
Hard Drive
4 steps
Upper Case
7 steps
PRAM Battery
2 steps

Flags

BackHP Mini 1000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

With the case closed, place the Mini 1000 top-side down on a flat surface.
Push both of the battery release latches toward each other.

With the case closed, place the Mini 1000 top-side down on a flat surface.

Push both of the battery release latches toward each other.

1024

Step 2

Lift the battery out of the Mini 1000 from the edge closest to the release latches.

Lift the battery out of the Mini 1000 from the edge closest to the release latches.

Step 3

              Keyboard

Remove the following two screws:
One 6 mm Phillips screw
One 4 mm Phillips screw

Remove the following two screws:

One 6 mm Phillips screw

One 4 mm Phillips screw

Step 4

To facilitate the removal of the keyboard, it is recommended to push the keyboard outwards with one hand through the opening (highlighted in the third picture) located on the backside of the Mini 1000.
While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you.
Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.

To facilitate the removal of the keyboard, it is recommended to push the keyboard outwards with one hand through the opening (highlighted in the third picture) located on the backside of the Mini 1000.

While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you.

Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.

Step 5

Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.

Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.

Step 6

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.
Be sure you are prying up on the retaining flap, not the socket itself.
Pull the cable out of its socket and remove the keyboard.

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.

Be sure you are prying up on the retaining flap, not the socket itself.

Pull the cable out of its socket and remove the keyboard.

Step 7

              Hard Drive

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket.
Be sure you are prying up on the retaining flap, not the socket itself.
Pull the SIM card ribbon cable out of its socket and peel it off the top of the hard drive enclosure.

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket.

Pull the SIM card ribbon cable out of its socket and peel it off the top of the hard drive enclosure.

Step 8

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.
Be sure you are prying up on the retaining flap, not the socket itself.

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.

Step 9

Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.

Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.

Step 10

Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.

Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.

Step 11

              Upper Case

Using the sharp tip of a spudger, pry and remove the four plastic screw covers from the underside of the HP Mini 1000.
There are three different variations of the covers:
The two bottom covers are short in height and are notched to prevent incorrect insertion
The upper right cover is taller in height and is notched.
The upper left cover is taller in height and is not notched.

Using the sharp tip of a spudger, pry and remove the four plastic screw covers from the underside of the HP Mini 1000.

There are three different variations of the covers:

The two bottom covers are short in height and are notched to prevent incorrect insertion

The upper right cover is taller in height and is notched.

The upper left cover is taller in height and is not notched.

Step 12

Remove the four 7 mm Phillips screws that secure the upper case to the lower case.

Remove the four 7 mm Phillips screws that secure the upper case to the lower case.

Step 13

Flip the computer over and open the display.
Remove the two 4.5 mm Phillips screws securing the upper case to the lower case.

Flip the computer over and open the display.

Remove the two 4.5 mm Phillips screws securing the upper case to the lower case.

Step 14

Wedge the flat end of a spudger in between the upper case and lower case near the bottom right corner of the display.
Carefully pry and rock the spudger upwards to create a small gap between the upper case and lower case.
Continue the previously described motion along the right edge of the upper case to release the clips securing the upper case to the lower case.

Wedge the flat end of a spudger in between the upper case and lower case near the bottom right corner of the display.

Carefully pry and rock the spudger upwards to create a small gap between the upper case and lower case.

Continue the previously described motion along the right edge of the upper case to release the clips securing the upper case to the lower case.

Step 15

Repeat the same procedure as mentioned in the previous step to release the clips along the left side of the upper case.

Repeat the same procedure as mentioned in the previous step to release the clips along the left side of the upper case.

Step 16

Grasp the upper case and carefully lift it slightly upwards, freeing it from any remaining clips.
The upper case is still attached via the TouchPad ribbon cable that is connected to the motherboard. Do not remove it completely just yet.

Grasp the upper case and carefully lift it slightly upwards, freeing it from any remaining clips.

The upper case is still attached via the TouchPad ribbon cable that is connected to the motherboard. Do not remove it completely just yet.

Step 17

Lay the upper case on top of the upper portion of the motherboard.
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the TouchPad cable ZIF socket.
Be sure you are prying up on the retaining flap, not the socket itself.
Pull the TouchPad ribbon cable out of its socket.
Remove the upper case from the HP Mini 1000.

Lay the upper case on top of the upper portion of the motherboard.

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the TouchPad cable ZIF socket.

Pull the TouchPad ribbon cable out of its socket.

Remove the upper case from the HP Mini 1000.

Step 18

              PRAM Battery

If present, carefully peel back the large piece of black film attached to the heat sink to reveal the PRAM battery and its connector.
It is not necessary to completely remove this film.

If present, carefully peel back the large piece of black film attached to the heat sink to reveal the PRAM battery and its connector.

It is not necessary to completely remove this film.

Step 19

Use a pair of tweezers to pull the PRAM battery connector out of its socket.
Pull the connector parallel to the face of the motherboard toward the fan side of the computer.
Use the flat end of a spudger to pry the PRAM battery off the adhesive securing it to the motherboard.
Remove the PRAM battery.

Use a pair of tweezers to pull the PRAM battery connector out of its socket.

Pull the connector parallel to the face of the motherboard toward the fan side of the computer.

Use the flat end of a spudger to pry the PRAM battery off the adhesive securing it to the motherboard.

Remove the PRAM battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors

                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

Jake Stitt - Jul 21, 2016

Where can you find the replacement battery for this? do you take it apart and slide in a cr2016 watch battery?

The Eminent Joshua E. Hrouda - Jan 10, 2021

Try eBay. If you can solder, it’s best to get a CR1616 with tabs

Κωνσταντίνος Σακελλαρόπουλος - Jun 13, 2018

whhere cann youu findd a replacement bbattery in 2018

The Eminent Joshua E. Hrouda - Jan 10, 2021

Is there enough room to install a CR2020 or a CR2025?

Introduction#

What you need#

Introduction

What you need