Difficulty
Moderate
Steps
9
Time Required
10 - 15 minutes
Sections
1
- Power Button
- 9 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackHP Laserjet Pro 200 Color MFP
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Power Button
- Turn the printer so that the front is facing to your left.
- Flip the printer so that it is laying with its left side facing down and the bottom facing you.
Turn the printer so that the front is facing to your left.
Flip the printer so that it is laying with its left side facing down and the bottom facing you.
1024
Step 2
- Use a #2 Phillips head screwdriver to unscrew the 8mm screw on the top edge of the printer.
Use a #2 Phillips head screwdriver to unscrew the 8mm screw on the top edge of the printer.
Step 3
- There are three tabs along the back right corner of the printer underneath the panel (location is displayed in the second picture).
- Use a flathead screwdriver to depress the tabs while lightly pulling the panel towards you.
- Begin with the upmost tab and move your way down, individually depressing the tabs.
- Pull the panel towards you and remove it from the printer.
There are three tabs along the back right corner of the printer underneath the panel (location is displayed in the second picture).
Use a flathead screwdriver to depress the tabs while lightly pulling the panel towards you.
Begin with the upmost tab and move your way down, individually depressing the tabs.
Pull the panel towards you and remove it from the printer.
Step 4
- Turn the printer so that you are facing the open side with the power button chord.
- Carefully remove this cord.
Turn the printer so that you are facing the open side with the power button chord.
Carefully remove this cord.
Step 5
- There is a cover that protects the electronics within the power button.
- Remove it by pinching the two tabs on the cover.
- Pull it outward from the printer.
There is a cover that protects the electronics within the power button.
Remove it by pinching the two tabs on the cover.
Pull it outward from the printer.
Step 6
- A tension spring in the form of a bent wire is used to hold the assembly in the printer.
- In order to remove the spring completely, begin by removing the right end of the wire from it’s slot above the power button with a metal spudger.
A tension spring in the form of a bent wire is used to hold the assembly in the printer.
In order to remove the spring completely, begin by removing the right end of the wire from it’s slot above the power button with a metal spudger.
Step 7
- Unclip the left side of the wire from printer by applying upwards pressure along the edge of the wire.
- This step can be done with either your fingers or a prying tool of your choosing.
Unclip the left side of the wire from printer by applying upwards pressure along the edge of the wire.
This step can be done with either your fingers or a prying tool of your choosing.
Step 8
- Grab the wire and hold it firmly with two fingers.
- Pull it directly upwards.
- Wiggle it until it is fully removed from the printer.
Grab the wire and hold it firmly with two fingers.
Pull it directly upwards.
Wiggle it until it is fully removed from the printer.
Step 9
- Pull the power button board directly towards you, until both the board and the wire are fully clear of the printer.
Pull the power button board directly towards you, until both the board and the wire are fully clear of the printer.
To reassemble your device, follow the instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
Kendall Gentzen
Member since: 04/18/2019
930 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team S9-G14, Maness Spring 2019
Member of Cal Poly, Team S9-G14, Maness Spring 2019
CPSU-MANESS-S19S9G14
4 Members
5 Guides authored
