Difficulty

Moderate

Steps

11

Time Required

                          25 - 30 minutes

Sections

2

  • Left Side Panel
  • 7 steps
  • Drive Belt
  • 4 steps

Flags

0

  • BackHP LaserJet P1102w

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Left Side Panel
  • Flip printer on it’s back. Using the plastic spudger, pry off front panel. There will be two main points to focus as shown.
  • Pry carefully to not break any plastic.

Flip printer on it’s back. Using the plastic spudger, pry off front panel. There will be two main points to focus as shown.

Pry carefully to not break any plastic.

1024

Step 2

  • Now that the pry points are free lift up the front panel.

Now that the pry points are free lift up the front panel.

Step 3

  • Unscrew the #1 Phillips screw 6mm on the back of the printer.

Unscrew the #1 Phillips screw 6mm on the back of the printer.

Step 4

  • Using the plastic spudger, remove the button housing from the top left of printer.
  • Pry carefully to not break any plastic.

Using the plastic spudger, remove the button housing from the top left of printer.

Step 5

  • Once the housing is removed, remove the three buttons.

Once the housing is removed, remove the three buttons.

Step 6

  • Use the plastic spudger to remove the side panel. There are three main prying points as shown.
  • Pry carefully to not break any plastic.

Use the plastic spudger to remove the side panel. There are three main prying points as shown.

Step 7

  • With all pry points free, remove the side panel.

With all pry points free, remove the side panel.

Step 8

              Drive Belt
  • Refer to the prerequisite guide to take off the front panel off.
  • With a #1 Phillips screwdriver remove only the top Phillips 60mm screw.
  • With the spudger pry the side panel off. There will be four flanges to unhitch.

Refer to the prerequisite guide to take off the front panel off.

With a #1 Phillips screwdriver remove only the top Phillips 60mm screw.

With the spudger pry the side panel off. There will be four flanges to unhitch.

Step 9

  • With side panel removed, there will be four Phillips 60mm screws to unscrew using a #1 Phillips screwdriver.

With side panel removed, there will be four Phillips 60mm screws to unscrew using a #1 Phillips screwdriver.

Step 10

  • Remove top two big gears using tweezers.
  • Take note of gear placement.

Remove top two big gears using tweezers.

Take note of gear placement.

Step 11

  • With the #1 Phillips screwdriver remove the 60mm Phillips screw holding the belt tension-er.
  • With the screw removed, pull tension-er out.
  • Use tweezers to remove the loose drive belt.

With the #1 Phillips screwdriver remove the 60mm Phillips screw holding the belt tension-er.

With the screw removed, pull tension-er out.

Use tweezers to remove the loose drive belt.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    Jerome Etten

Member since: 10/04/2018

571 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UW Stout, Team S6-G4, Ogden Fall 2018                        

                                                  Member of UW Stout, Team S6-G4, Ogden Fall 2018 



                    UWSTOUT-OGDEN-F18S6G4                     


                                            4 Members                     


                                            5 Guides authored