Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

1

  • Hard Disk
  • 8 steps

Flags

4

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackRéparation HP Laptop 15-g000sl

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Step 1

              Hard Disk
  • Remove the battery by moving the points marked with an arrow towards the inside.

Remove the battery by moving the points marked with an arrow towards the inside.

1024

Step 2

  • Remove the glued rear rubber feet , optionally use a heat source such as a hair dryer
  • Using a Phillips screwdriver, remove the 2 screws underneath the rubber stopper

Remove the glued rear rubber feet , optionally use a heat source such as a hair dryer

Using a Phillips screwdriver, remove the 2 screws underneath the rubber stopper

Step 3

  • Remove all visible screws at the bottom.

Remove all visible screws at the bottom.

Step 4

  • Remove the keyboard with the help of a thin tool.
  • Be careful because it is connected to the cable, then unhook the connector.

Remove the keyboard with the help of a thin tool.

Be careful because it is connected to the cable, then unhook the connector.

Step 5

  • Unhook the 2 connectors and remove the 4 screws.

Unhook the 2 connectors and remove the 4 screws.

Step 6

  • Extract DVD player.
  • Remove the 2 screws indicated in the second picture.

Extract DVD player.

Remove the 2 screws indicated in the second picture.

Step 7

  • It is possible to remove the upper cover which is free of screws and only hooked by a joint with the help of a thin tool.

It is possible to remove the upper cover which is free of screws and only hooked by a joint with the help of a thin tool.

Step 8

  • Remove the 2 hard disk fastening screws.
  • Remove the disc sideways.
  • Take away the support by removing the 2 screws to place it on the new hard disk

Remove the 2 hard disk fastening screws.

Remove the disc sideways.

Take away the support by removing the 2 screws to place it on the new hard disk

To reassemble the device, follow the steps of this guide in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Mariana Roca

Corey Meyer

Author

                                      with 1 other contributor 


                    Smilzo

Member since: 11/09/2013

10,473 Reputation

                                      39 Guides authored                  



                       Badges:
                       23







                                                        +20 more badges

A Prosaic Hacker - Feb 15, 2022

Reply

I did a similar clone hd to ssd replacement on Hewlett Packard 15-bs058ca Laptop. It was a full bottom removal with the components attached to the bottom of the keyboard and screen combo. There were hidden screws under the rubber feet. A lot of finicky spludger work all around the outer shell was needed to pry the bottom from the top. The good thing was there are no cables between the bottom shell and the rest of the laptop.

After that the hard-disk change was similar to the one above.

HP does have a manual (http://h10032.www1.hp.com/ctg/Manual/c05…) but it does not mention the care needed to pry apart the shell.

Next time I do this I will take photos and up load them.