Difficulty

Moderate

Steps

7

Time Required

                          10 - 15 minutes

Sections

2

  • Keyboard
  • 4 steps
  • Motherboard
  • 3 steps

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackHP Envy x360 m6-w103dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Wear the anti-static wrist strap and attach it to a metal surface to avoid damaging sensitive electrical components. Make sure the computer is unplugged and powered off before touching any internal parts.

The motherboard isn’t a hazardous component to handle, but it is connected to many critical parts of the computer and must be removed with care.

What you need

Step 1

              Keyboard
  • Before you begin, be sure to power off your laptop.
  • Using an opening pick, remove the 4 rubber feet and 4 screw covers.

Before you begin, be sure to power off your laptop.

Using an opening pick, remove the 4 rubber feet and 4 screw covers.

1024

Step 2

  • Unscrew the twelve 6 mm screws from the bottom of the laptop using a Phillips #0 screwdriver.

Unscrew the twelve 6 mm screws from the bottom of the laptop using a Phillips #0 screwdriver.

Step 3

  • Open the laptop carefully, with the keyboard face up.
  • Pry around the outside of the keyboard with the plastic opening tool until the keyboard can be lifted slightly.
  • When lifting the keyboard do not pull too hard. There are cables that must be disconnected before the keyboard can be removed.

Open the laptop carefully, with the keyboard face up.

Pry around the outside of the keyboard with the plastic opening tool until the keyboard can be lifted slightly.

When lifting the keyboard do not pull too hard. There are cables that must be disconnected before the keyboard can be removed.

Step 4

  • Lift the keyboard until you can see the cables connected to the motherboard.
  • Gently lift the tab on each ZIF connector that connects each cable to the motherboard using a spudger. Once each tab is flipped up, the corresponding ribbon cable will come out easily.
  • Detach the keyboard.

Lift the keyboard until you can see the cables connected to the motherboard.

Gently lift the tab on each ZIF connector that connects each cable to the motherboard using a spudger. Once each tab is flipped up, the corresponding ribbon cable will come out easily.

Detach the keyboard.

Step 5

              Motherboard
  • Disconnect the pin head battery connection to remove power from the motherboard.
  • Unscrew the five 4mm screws holding the motherboard in place using a #0 Phillips screwdriver.
  • It’s possible the positions of the screws will be different on your board. If the motherboard resists lifting, double-check that all screws have been removed.

Disconnect the pin head battery connection to remove power from the motherboard.

Unscrew the five 4mm screws holding the motherboard in place using a #0 Phillips screwdriver.

It’s possible the positions of the screws will be different on your board. If the motherboard resists lifting, double-check that all screws have been removed.

Step 6

  • Remove the five flat ribbon cables by gently lifting the head of the cable up and back.
  • Remove the two remaining multicolored ribbon cables by pulling the white plastic head backwards.
  • Do not pull directly on the wires.
  • If the head of the multicolored ribbon cable doesn’t come out, try gently wiggling it side to side as you pull.

Remove the five flat ribbon cables by gently lifting the head of the cable up and back.

Remove the two remaining multicolored ribbon cables by pulling the white plastic head backwards.

Do not pull directly on the wires.

If the head of the multicolored ribbon cable doesn’t come out, try gently wiggling it side to side as you pull.

Step 7

  • Lift the motherboard up from the left side at a shallow angle.
  • Gently pull the motherboard to the left and gently wiggle it side to side until the ports on the right side of the board detach from the case.
  • Ensure the laptop is well supported, as the motherboard is a heavy component and removing it may make the laptop off-balance.

Lift the motherboard up from the left side at a shallow angle.

Gently pull the motherboard to the left and gently wiggle it side to side until the ports on the right side of the board detach from the case.

Ensure the laptop is well supported, as the motherboard is a heavy component and removing it may make the laptop off-balance.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Steven Ngo

Member since: 10/10/2019

835 Reputation

                                      7 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team S12-G2, Regan Fall 2019                        

                                                  Member of Cal Poly, Team S12-G2, Regan Fall 2019 



                    CPSU-REGAN-F19S12G2                     


                                            4 Members                     


                                            23 Guides authored

Frank - Apr 24, 2020

Reply

Can I Change the graphics card only?

Is there a way to fix only the graphics card?

Isaac Zachary - Apr 29, 2021

Reply

I wonder if it’s possible to solder on an M.2 header on that SSD1 spot on the board.