Difficulty
Moderate
Steps
10
Time Required
5 minutes
Sections
3
- Bottom Cover
- 4 steps
- Battery
- 3 steps
- Intel Wireless Module
- 3 steps
Flags
0
BackHP Envy x360 m6-aq103dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Bottom Cover
- Flip the laptop over to expose the underside.
- Remove the two grip pads with blue plastic opening tool by inserting the tool between the laptop and the pads and slowly lifting up.
- The grip pads are tacky, remove slowly to avoid separating the adhesive.
Flip the laptop over to expose the underside.
Remove the two grip pads with blue plastic opening tool by inserting the tool between the laptop and the pads and slowly lifting up.
The grip pads are tacky, remove slowly to avoid separating the adhesive.
1024
Step 2
- Remove the two 8 mm Phillips Head screws that were under the grip pads using a Phillip’s Head 1 Screwdriver.
Remove the two 8 mm Phillips Head screws that were under the grip pads using a Phillip’s Head 1 Screwdriver.
Step 3
- Remove the six 5 mm Torx screws using a T5 Torx Screwdriver.
Remove the six 5 mm Torx screws using a T5 Torx Screwdriver.
Step 4
- Use the nylon spudger to pop off the bottom cover by inserting it into the heat vent and twisting to the left or right.
- You may hear a slight clicking or popping, but that is normal.
Use the nylon spudger to pop off the bottom cover by inserting it into the heat vent and twisting to the left or right.
You may hear a slight clicking or popping, but that is normal.
Step 5
Battery
- Use the Phillips Head 1 Screwdriver to remove the six 4 mm screws.
Use the Phillips Head 1 Screwdriver to remove the six 4 mm screws.
Step 6
- Disconnect the battery port from the motherboard by gently lifting it on both sides with the plastic opening tool.
- Lift up the port with the tool.
Disconnect the battery port from the motherboard by gently lifting it on both sides with the plastic opening tool.
Lift up the port with the tool.
Step 7
- Lift the battery out of the laptop with your hands.
Lift the battery out of the laptop with your hands.
Step 8
Intel Wireless Module
- Remove the two antenna cables connected to the wireless module by wedging the small plastic opening tool between the cables and the wireless module and lifting up.
Remove the two antenna cables connected to the wireless module by wedging the small plastic opening tool between the cables and the wireless module and lifting up.
Step 9
- Remove the 3.5 mm Phillips Head screw with the Phillip Head 1 screwdriver.
Remove the 3.5 mm Phillips Head screw with the Phillip Head 1 screwdriver.
Step 10
- Slide the wireless module towards the back of the computer to remove it.
Slide the wireless module towards the back of the computer to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Joey Chen
Member since: 10/02/2017
313 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team S4-G3, Livingston Fall 2017
Member of Cal Poly, Team S4-G3, Livingston Fall 2017
CPSU-LIVINGSTON-F17S4G3
4 Members
9 Guides authored
Al N - Aug 4, 2019
Reply
@jchen202 Just curious, what is the Battery Wattage of this HP Envy? I noticed your guide contains a glimpse of the DC IN CONNECTOR , which seems to be identical to my HP ENVY X360 - 15M-BP112DX. How idid your repairs turn out? If possible, would you be able to provide a picture of the DC IN Connector?
