Difficulty
Moderate
Steps
15
Time Required
1 - 2 hours
Sections
5
- Battery
- 5 steps
- Cooling Fan
- 4 steps
- Motherboard
- 3 steps
- Speakers
- 1 step
- Power Input
- 2 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackHP Envy x360 15m-bq021dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- On the back panel of the device, remove the four (4) M2.5xL6 screws at the top of the photo using a Phillips #0 screwdriver.
- Unscrew the three (3) screws at the bottom of the photo using a T5 Torx screwdriver.
On the back panel of the device, remove the four (4) M2.5xL6 screws at the top of the photo using a Phillips #0 screwdriver.
Unscrew the three (3) screws at the bottom of the photo using a T5 Torx screwdriver.
1024
Step 2
- To remove the back cover, use the black spudger to lift up on the edges of the cover.
- Use a suction cup to assist in lifting the back cover
To remove the back cover, use the black spudger to lift up on the edges of the cover.
Use a suction cup to assist in lifting the back cover
Step 3
- Use the Philips #0 screwdriver to remove six (6) M2.0x3.2 screws from battery.
Use the Philips #0 screwdriver to remove six (6) M2.0x3.2 screws from battery.
Step 4
- Using the Philips #0 screwdriver, remove the final screw from the battery connected to the SSD storage unit.
Using the Philips #0 screwdriver, remove the final screw from the battery connected to the SSD storage unit.
Step 5
- Lift and pull the front of the battery up and out (away from the connector) to remove.
Lift and pull the front of the battery up and out (away from the connector) to remove.
Step 6
Cooling Fan
- Using a Philips #0 screwdriver, remove the three M2x4 screws located around the cooling fan as shown in this picture.
- Be careful as the fan might be sharp in some places when removing it.
Using a Philips #0 screwdriver, remove the three M2x4 screws located around the cooling fan as shown in this picture.
Be careful as the fan might be sharp in some places when removing it.
Step 7
- Remove the connector clip with the tweezers.
Remove the connector clip with the tweezers.
Step 8
- Remove the four spring loaded screws with a Philips #1 screwdriver.
Remove the four spring loaded screws with a Philips #1 screwdriver.
Step 9
- Remove the cooling fan.
Remove the cooling fan.
Step 10
Motherboard
- Using a Phillips #1, remove the seven M2.0x3.2 screws.
- Undo the six connections using the blue opening tool.
Using a Phillips #1, remove the seven M2.0x3.2 screws.
Undo the six connections using the blue opening tool.
Step 11
- Carefully remove the aux port from the frame of the computer as shown.
Carefully remove the aux port from the frame of the computer as shown.
Step 12
- Pull the mother board up and away from frame of the computer.
Pull the mother board up and away from frame of the computer.
Step 13
Speakers
- Use the tweezers to remove the cords from their restraints.
- Lift the speakers out of the laptop.
Use the tweezers to remove the cords from their restraints.
Lift the speakers out of the laptop.
Step 14
Power Input
- Remove the three M2.0x3.2 hinge screws next to the power input cord using a Philips #0 screwdriver.
- Pry the hinge up so that it is out of the way.
Remove the three M2.0x3.2 hinge screws next to the power input cord using a Philips #0 screwdriver.
Pry the hinge up so that it is out of the way.
Step 15
- Lift out the power input.
Lift out the power input.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Julie Bengoa
Member since: 01/18/2022
85 Reputation
1 Guide authored
Badges:
3
Team
Embry-Riddle Aeronautical University, Team 2-3, Rauch Spring 2022
Member of Embry-Riddle Aeronautical University, Team 2-3, Rauch Spring 2022
ERAU-RAUCH-S22S2G3
3 Members
3 Guides authored
