Difficulty

Moderate

Steps

8

Time Required

                          15 - 25 minutes

Sections

2

  • Back Panel
  • 2 steps
  • Charging Port
  • 6 steps

Flags

0

  • BackHP Envy x360 15m-bp111dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Be sure that your laptop is powered off, disconnected from the charging adapter, and that the components have cooled before beginning this replacement.

What you need

Step 1

              Back Panel
  • Remove the rubber feet to access the screws.
  • Using a Phillips #0 screwdriver, remove the four 7 mm screws.
  • Using a T5 Torx screwdriver, remove the three 5 mm screws.

Remove the rubber feet to access the screws.

Using a Phillips #0 screwdriver, remove the four 7 mm screws.

Using a T5 Torx screwdriver, remove the three 5 mm screws.

1024

Step 2

  • Insert opening picks or an opening tool inside the edge of the chassis to separate the back panel from the rest of the computer.
  • You may hear snapping as the clips are released while you work your way around the perimeter of the computer. This is normal.
  • Remove the back case.

Insert opening picks or an opening tool inside the edge of the chassis to separate the back panel from the rest of the computer.

You may hear snapping as the clips are released while you work your way around the perimeter of the computer. This is normal.

Remove the back case.

Step 3

              Charging Port
  • Use a Phillips #0 screwdriver to remove the two M2x3.1 screws that secure the speaker in place.
  • Lift and move the speaker to the side.
  • Do not pull too hard on the speaker. It is connected by thin wires that run under the motherboard.

Use a Phillips #0 screwdriver to remove the two M2x3.1 screws that secure the speaker in place.

Lift and move the speaker to the side.

Do not pull too hard on the speaker. It is connected by thin wires that run under the motherboard.

Step 4

  • Use a Phillips #0 screwdriver to remove remove three M2.5x4 screws that secure the hinge.

Use a Phillips #0 screwdriver to remove remove three M2.5x4 screws that secure the hinge.

Step 5

  • Use the opening tool to raise the hinge.
  • Then lift the hinge by hand to provide enough clearance to remove the charging port.
  • Be careful when lifting the hinge. The back can be bent and damaged if raised too far.

Use the opening tool to raise the hinge.

Then lift the hinge by hand to provide enough clearance to remove the charging port.

Be careful when lifting the hinge. The back can be bent and damaged if raised too far.

Step 6

  • Gently slide the charging port connector out of the port, and lift it above the hinge.

Gently slide the charging port connector out of the port, and lift it above the hinge.

Step 7

  • Grasp the sliding connector on the motherboard and remove it from the socket.

Grasp the sliding connector on the motherboard and remove it from the socket.

Step 8

  • Remove the charging port.

Remove the charging port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Tori Luongo

Member since: 02/22/2022

241 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Clemson, Team 2-2, Hunter Spring 2022                        

                                                  Member of Clemson, Team 2-2, Hunter Spring 2022 



                    CLEM-HUNTER-S22S2G2                     


                                            5 Members                     


                                            6 Guides authored