Difficulty
Moderate
Steps
9
Time Required
10 - 15 minutes
Sections
2
- Battery
- 7 steps
- Wi-Fi Card
- 2 steps
Flags
0
BackHP Envy x360 15-u473cl
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Power off your laptop before beginning disassembly.
- Pry off the 2 rear rubber pads (closest to the laptop hinge) using the plastic opening tool to reveal two screws.
- Remove the 2 anti-tamper proof covers using the spudger to reveal two screws.
Power off your laptop before beginning disassembly.
Pry off the 2 rear rubber pads (closest to the laptop hinge) using the plastic opening tool to reveal two screws.
Remove the 2 anti-tamper proof covers using the spudger to reveal two screws.
1024
Step 2
- Remove the fourteen 7mm screws using the Phillips #0 screwdriver from the bottom of the laptop.
Remove the fourteen 7mm screws using the Phillips #0 screwdriver from the bottom of the laptop.
Step 3
- Turn the device right side up and open the lid.
- Insert the plastic opening tool in between the keyboard plate and the base of laptop.
- Run the tool along seem, prying up as you go.
- Separate the keyboard plate from the base, lifting from the front.
Turn the device right side up and open the lid.
Insert the plastic opening tool in between the keyboard plate and the base of laptop.
Run the tool along seem, prying up as you go.
Separate the keyboard plate from the base, lifting from the front.
Step 4
- There are 3 ribbon cables (black, white, and copper color) connecting the computer to the keyboard plate. Disconnect the 3 ribbon cables using the plastic opening tool by prying up the latches holding each cable in place.
- Remove the keyboard plate from the device.
There are 3 ribbon cables (black, white, and copper color) connecting the computer to the keyboard plate. Disconnect the 3 ribbon cables using the plastic opening tool by prying up the latches holding each cable in place.
Remove the keyboard plate from the device.
Step 5
- Remove the thick white ribbon cable covering the battery using the plastic opening tool by prying up the latches attaching each end.
Remove the thick white ribbon cable covering the battery using the plastic opening tool by prying up the latches attaching each end.
Step 6
- Remove the three 4mm screws using the Phillips #0 screwdriver.
Remove the three 4mm screws using the Phillips #0 screwdriver.
Step 7
- Disconnect the battery from the motherboard.
- There may be tamper-proof tape holding the battery in place. Remove the tape if present.
- Remove the battery from the device.
Disconnect the battery from the motherboard.
There may be tamper-proof tape holding the battery in place. Remove the tape if present.
Remove the battery from the device.
Step 8
Wi-Fi Card
- Remove one 3mm screw with the Phillips #00 screwdriver.
Remove one 3mm screw with the Phillips #00 screwdriver.
Step 9
- Disconnect the wireless card by pulling away from the black connector using the spudger.
- Push up on the two wires to release the connectors and remove the Wi-Fi card from the device.
Disconnect the wireless card by pulling away from the black connector using the spudger.
Push up on the two wires to release the connectors and remove the Wi-Fi card from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Matthew Ortman
Member since: 11/07/2019
163 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
IUPUI, Team S3-G3, Harley Fall 2019
Member of IUPUI, Team S3-G3, Harley Fall 2019
IUPUI-HARLEY-F19S3G3
3 Members
2 Guides authored
