Difficulty

Moderate

Steps

11

Time Required

                          30 - 45 minutes

Sections

2

  • Battery
  • 6 steps
  • Motherboard
  • 5 steps

Flags

0

  • BackHP Envy x360 15-bp143cl

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Flip the laptop over.
  • Peel off the rubber strip closest to the hinges.

Flip the laptop over.

Peel off the rubber strip closest to the hinges.

1024

Step 2

  • Use a Phillips #1 screwdriver (PH1 bit) to remove the four 6.5mm screws that were underneath the rubber strip.

Use a Phillips #1 screwdriver (PH1 bit) to remove the four 6.5mm screws that were underneath the rubber strip.

Step 3

  • Use a Torx T5 screwdriver (T5 bit) to remove the three 5mm screws near the bottom edge of the laptop.

Use a Torx T5 screwdriver (T5 bit) to remove the three 5mm screws near the bottom edge of the laptop.

Step 4

  • Lift the back panel to remove it from the laptop.
  • Use an opening tool to pry open the back panel if it does not easily lift apart.

Lift the back panel to remove it from the laptop.

Use an opening tool to pry open the back panel if it does not easily lift apart.

Step 5

  • Use a Phillips #1 screwdriver (PH1) to remove the seven 4mm screws indicated by the gray arrows on the battery.

Use a Phillips #1 screwdriver (PH1) to remove the seven 4mm screws indicated by the gray arrows on the battery.

Step 6

  • Pull the battery from the connecting port and lift to remove it from the laptop.

Pull the battery from the connecting port and lift to remove it from the laptop.

Step 7

              Motherboard
  • Peel off the tape securing the heatsink.

Peel off the tape securing the heatsink.

Step 8

  • Use a Phillips #1 screwdriver to remove the seven 4 mm screws securing the fan.
  • Detach the fan cable from the mother board.

Use a Phillips #1 screwdriver to remove the seven 4 mm screws securing the fan.

Detach the fan cable from the mother board.

Step 9

  • Lift the fan up and off the motherboard.

Lift the fan up and off the motherboard.

Step 10

  • Use a Phillips #1 screwdriver to remove the ten 4 mm screws securing the motherboard.
  • Pull the four cables directly out of their ports.
  • Flip up the lock-bar on the two ZIF connectors, then gently pull the two ribbon cables directly out of their ports.

Use a Phillips #1 screwdriver to remove the ten 4 mm screws securing the motherboard.

Pull the four cables directly out of their ports.

Flip up the lock-bar on the two ZIF connectors, then gently pull the two ribbon cables directly out of their ports.

Step 11

  • Gently lift the motherboard up and out of the chassis.

Gently lift the motherboard up and out of the chassis.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Thomas Schemm

Member since: 02/11/2022

289 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       The Citadel Military College of South Carolina, Team 1-2, Eggleston Spring 2022                        

                                                  Member of The Citadel Military College of South Carolina, Team 1-2, Eggleston Spring 2022 



                    CMCSC-EGGLESTON-S22S1G2                     


                                            2 Members                     


                                            3 Guides authored