Difficulty
Moderate
Steps
13
Time Required
20 minutes
Sections
2
- Battery
- 8 steps
- Motherboard
- 5 steps
Flags
0
BackHP Envy x2 13-j002dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove five 4mm Phillips #0 screws securing the lower case to the HP Envy x2 13-j002dx.
Remove five 4mm Phillips #0 screws securing the lower case to the HP Envy x2 13-j002dx.
1024
Step 2
- Use a Phillips #00 screwdriver to remove the two 3.5 mm screws from the bottom of the device—one on each side of the keyboard dock.
Use a Phillips #00 screwdriver to remove the two 3.5 mm screws from the bottom of the device—one on each side of the keyboard dock.
Step 3
- Use a pair of tweezers to remove the screw covers on the bottom of the device.
- Use a Phillips #0 screwdriver to remove the two 4mm screws.
Use a pair of tweezers to remove the screw covers on the bottom of the device.
Use a Phillips #0 screwdriver to remove the two 4mm screws.
Step 4
- Use an opening pick to remove the plastic cover above the back stand.
- Pry the cover off.
- Use a Phillips #0 screwdriver to remove the four 4 mm screws.
Use an opening pick to remove the plastic cover above the back stand.
Pry the cover off.
Use a Phillips #0 screwdriver to remove the four 4 mm screws.
Step 5
- Use an opening pick and a prying tool, and go around the device to remove the back cover from the rest of the assembly.
Use an opening pick and a prying tool, and go around the device to remove the back cover from the rest of the assembly.
Step 6
- Unplug the battery from the motherboard.
Unplug the battery from the motherboard.
Step 7
- Carefully pull up on the battery connector from the speaker.
- Use a pair of tweezers and remove the taped down wire for the speaker.
- Use a Phillips #00 screwdriver to remove the seven 3mm screws around the battery.
Carefully pull up on the battery connector from the speaker.
Use a pair of tweezers and remove the taped down wire for the speaker.
Use a Phillips #00 screwdriver to remove the seven 3mm screws around the battery.
Step 8
- Carefully lift up and remove the battery.
Carefully lift up and remove the battery.
Step 9
Motherboard
- Before removing the motherboard, clear away any dust, and ensure that the battery is already removed.
Before removing the motherboard, clear away any dust, and ensure that the battery is already removed.
Step 10
- Using a Phillips #0 screwdriver, remove the three 3.8 mm screws along the edge of the motherboard.
Using a Phillips #0 screwdriver, remove the three 3.8 mm screws along the edge of the motherboard.
Step 11
- Disconnect the cable connectors from the motherboard. This can be done with either tweezers or with your fingers.
Disconnect the cable connectors from the motherboard. This can be done with either tweezers or with your fingers.
Step 12
- Using the Phillips #0 screwdriver, remove the 3.2mm screws within the copper rings in the circuit board.
- Using the Phillips #0 screwdriver, remove the 2.5mm and 4.25mm black screws on the motherboard.
Using the Phillips #0 screwdriver, remove the 3.2mm screws within the copper rings in the circuit board.
Using the Phillips #0 screwdriver, remove the 2.5mm and 4.25mm black screws on the motherboard.
Step 13
- Once the screws and cables are disconnected and removed, remove the motherboard from the frame.
Once the screws and cables are disconnected and removed, remove the motherboard from the frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Colton Moon
Member since: 11/04/2019
241 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
Idaho State University, Team S1-G3, Watkins Fall 2019
Member of Idaho State University, Team S1-G3, Watkins Fall 2019
ISU-WATKINS-F19S1G3
3 Members
2 Guides authored
