Difficulty
Moderate
Steps
12
Time Required
5 - 10 minutes
Sections
2
- Battery
- 9 steps
- Hard Disk Drive
- 3 steps
Flags
0
BackHP Envy Ultrabook 4-1015dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Make sure that the device is turned off and that all external devices are removed.
Make sure that the device is turned off and that all external devices are removed.
1024
Step 2
- Flip the device over so that the back plate is facing upwards.
Flip the device over so that the back plate is facing upwards.
Step 3
- Using a small (size 0) Phillips head screwdriver, remove the twelve 5.5 mm external Phillips head screws that connect the back plate to the device.
- Make sure to set the screws aside in a safe place so that you do not lose them, as they will be needed to reattach the backplate later.
Using a small (size 0) Phillips head screwdriver, remove the twelve 5.5 mm external Phillips head screws that connect the back plate to the device.
Make sure to set the screws aside in a safe place so that you do not lose them, as they will be needed to reattach the backplate later.
Step 4
- Using the plastic opening tool, gently pry off the back plate from the device.
Using the plastic opening tool, gently pry off the back plate from the device.
Step 5
- The large black box with the white warning images is the battery.
- Move the ribbon cable so that it is no longer on top of the battery.
The large black box with the white warning images is the battery.
Move the ribbon cable so that it is no longer on top of the battery.
Step 6
- Using a small (size 0) Phillips head screwdriver, remove the three 3.5 mm Phillips head internal screws that hold the battery in place.
- Make sure not to lose these internal screws; they will later be used to reattach the battery.
Using a small (size 0) Phillips head screwdriver, remove the three 3.5 mm Phillips head internal screws that hold the battery in place.
Make sure not to lose these internal screws; they will later be used to reattach the battery.
Step 7
- Lift up the battery and remove it from the slot as shown.
Lift up the battery and remove it from the slot as shown.
Step 8
- Use the plastic opening tool to disconnect the battery cable.
Use the plastic opening tool to disconnect the battery cable.
Step 9
- Lift up the battery and remove it from the device.
Lift up the battery and remove it from the device.
Step 10
Hard Disk Drive
- The hard disk drive is under a metallic looking case in the bottom-right corner of the device.
- Using a size 0 Phillips head screwdriver, remove the four 3 mm size 0 screws attaching the hard drive casing to the device.
The hard disk drive is under a metallic looking case in the bottom-right corner of the device.
Using a size 0 Phillips head screwdriver, remove the four 3 mm size 0 screws attaching the hard drive casing to the device.
Step 11
- Remove the hard drive case.
Remove the hard drive case.
Step 12
- Unplug the hard drive from the hard drive plug.
Unplug the hard drive from the hard drive plug.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Cameron DiBenedetto
Member since: 10/17/2018
97 Reputation
1 Guide authored
Badges:
2
Team
UMass Dartmouth, Team S1-G3, Valliere Fall 2018
Member of UMass Dartmouth, Team S1-G3, Valliere Fall 2018
UMASSD-VALLIERE-F18S1G3
5 Members
6 Guides authored
