Difficulty
Moderate
Steps
20
Time Required
20 - 25 minutes
Sections
3
- Battery
- 5 steps
- Fan
- 3 steps
- Keyboard
- 12 steps
Flags
0
BackHP Envy Sleekbook m6-k010dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the twelve 9 mm Phillips #00 screws.
Remove the twelve 9 mm Phillips #00 screws.
1024
Step 2
- Use the plastic opening tool and your hands to remove the bottom cover.
Use the plastic opening tool and your hands to remove the bottom cover.
Step 3
- Disconnect the battery power cable from the motherboard.
Disconnect the battery power cable from the motherboard.
Step 4
- Remove the six 6 mm Phillips #00 screws from the battery.
Remove the six 6 mm Phillips #00 screws from the battery.
Step 5
- Lift the battery out of the laptop.
Lift the battery out of the laptop.
Step 6
Fan
- Remove two 3mm Phillips #00 screws from the fan.
Remove two 3mm Phillips #00 screws from the fan.
Step 7
- Disconnect the fan cable by pulling it out of the motherboard socket.
Disconnect the fan cable by pulling it out of the motherboard socket.
Step 8
- Lift the fan upwards to remove it from the computer.
Lift the fan upwards to remove it from the computer.
Step 9
Keyboard
- Flip up the black tab on the ZIF connector and pull the blue and white flex cable connecting the touchpad to the motherboard.
Flip up the black tab on the ZIF connector and pull the blue and white flex cable connecting the touchpad to the motherboard.
Step 10
- Remove three 3mm Phillips #00 screws from the SD card board.
- Remove the SD card board.
Remove three 3mm Phillips #00 screws from the SD card board.
Remove the SD card board.
Step 11
- In order to remove the RAM, pull each silver clip (one at a time) away from the RAM.
- The RAM chip should pop up. Gently remove the RAM from the motherboard.
In order to remove the RAM, pull each silver clip (one at a time) away from the RAM.
The RAM chip should pop up. Gently remove the RAM from the motherboard.
Step 12
- Remove four 3mm Phillips #00 screws from the heatsink.
- Lift the heat sink out from the device and set it aside.
Remove four 3mm Phillips #00 screws from the heatsink.
Lift the heat sink out from the device and set it aside.
Step 13
- Remove the black and white antenna wires from the Wi-Fi card.
Remove the black and white antenna wires from the Wi-Fi card.
Step 14
- Remove the two 3mm Phillips #00 screws that secure the speaker to the device.
- Remove the four 4mm Phillips #00 screws from the bracket.
- Locate the speaker cable connecting the speaker to the audio board. Gently tug on this cable to dislodge. Set the speaker aside.
Remove the two 3mm Phillips #00 screws that secure the speaker to the device.
Remove the four 4mm Phillips #00 screws from the bracket.
Locate the speaker cable connecting the speaker to the audio board. Gently tug on this cable to dislodge. Set the speaker aside.
Step 15
- Remove the two 3mm Phillips #00 screws that secure the RJ-45 module.
- Lift the white tab on the ZIF connector and pull the ribbon cable out.
Remove the two 3mm Phillips #00 screws that secure the RJ-45 module.
Lift the white tab on the ZIF connector and pull the ribbon cable out.
Step 16
- Remove the 3mm Phillips #00 screw connecting the chip to the housing.
- Lift up silver bracket.
- Lift up the white flap on the ZIF connector and remove the purple ribbon cable.
Remove the 3mm Phillips #00 screw connecting the chip to the housing.
Lift up silver bracket.
Lift up the white flap on the ZIF connector and remove the purple ribbon cable.
Step 17
- Remove the cover for the RM-45 port.
- Gently lift and remove the chip from its housing.
Remove the cover for the RM-45 port.
Gently lift and remove the chip from its housing.
Step 18
- Remove the 4mm Phillips #00 screws.
- Remove the silver 3mm Phillips 3 mm screw.
- Lift all three black flaps in the ZIF connectors and remove the attached ribbon cables.
Remove the 4mm Phillips #00 screws.
Remove the silver 3mm Phillips 3 mm screw.
Lift all three black flaps in the ZIF connectors and remove the attached ribbon cables.
Step 19
- Use your hand and gently remove the connector to the back up battery for the motherboard.
- Remove the four 4mm Phillips #00 screws from the motherboard.
- Lift the board at an angle and pull outwards to dislodge it from the device.
Use your hand and gently remove the connector to the back up battery for the motherboard.
Remove the four 4mm Phillips #00 screws from the motherboard.
Lift the board at an angle and pull outwards to dislodge it from the device.
Step 20
- Remove the thirteen silver 3mm Phillips #00 screws that secure the keyboard to the frame.
- Lift up the keyboard from the bracket and pull outwards to remove the keyboard from the device.
Remove the thirteen silver 3mm Phillips #00 screws that secure the keyboard to the frame.
Lift up the keyboard from the bracket and pull outwards to remove the keyboard from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
codi whittaker
Member since: 02/14/2018
478 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
USF Tampa, Team S1-G4, Nance Spring 2018
Member of USF Tampa, Team S1-G4, Nance Spring 2018
USFT-NANCE-S18S1G4
4 Members
15 Guides authored
