Difficulty

Moderate

Steps

11

Time Required

                          15 minutes

Sections

3

  • Battery
  • 3 steps
  • Back Panel
  • 2 steps
  • Processor
  • 6 steps

Flags

0

  • BackHP Envy 17-J013CL

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Lay the laptop with the battery facing towards you.
  • Remember to disconnect the AC cable and other power sources from the device before replacing/repairing parts.

Lay the laptop with the battery facing towards you.

Remember to disconnect the AC cable and other power sources from the device before replacing/repairing parts.

1024

Step 2

  • Grab hold of the small battery slider and apply pressure to the right.
  • The laptop itself will push the battery out for you once the switch slides all the way to the right.

Grab hold of the small battery slider and apply pressure to the right.

The laptop itself will push the battery out for you once the switch slides all the way to the right.

Step 3

  • Pull the battery out and let go of the battery slider.

Pull the battery out and let go of the battery slider.

Step 4

              Back Panel
  • Use a PH1-screwdriver to loosen the 7mm screw. The screw will not fully come out as it is held by a washer underneath but will come out enough to open it.

Use a PH1-screwdriver to loosen the 7mm screw. The screw will not fully come out as it is held by a washer underneath but will come out enough to open it.

Step 5

  • Gently pull the back panel off starting from the battery side towards the back.
  • Pull it back as it snaps out of the holding sockets.
  • It is preferred to use both hands when pulling the back panel off to prevent bending it out of shape.

Gently pull the back panel off starting from the battery side towards the back.

Pull it back as it snaps out of the holding sockets.

It is preferred to use both hands when pulling the back panel off to prevent bending it out of shape.

Step 6

              Processor
  • Locate the 7mm screw for the optical drive right next to the WLAN and Memory modules.
  • Remove the screw with a PH1-screwdriver to release the CD-drive.

Locate the 7mm screw for the optical drive right next to the WLAN and Memory modules.

Remove the screw with a PH1-screwdriver to release the CD-drive.

Step 7

  • Use a PH1-Screwdriver to remove all the 7mm screws.
  • Use a PH0-Screwdriver to remove the 3mm screws.
  • Use the same PH0-Screwdriver for the 2mm screws.

Use a PH1-Screwdriver to remove all the 7mm screws.

Use a PH0-Screwdriver to remove the 3mm screws.

Use the same PH0-Screwdriver for the 2mm screws.

Step 8

  • Pull the under panel from the laptop by pulling at the edges once all screws are removed. Gently lift it off and place to the side.

Pull the under panel from the laptop by pulling at the edges once all screws are removed. Gently lift it off and place to the side.

Step 9

  • Unscrew the coiled springs indicated in red from the the motherboard.
  • Remove the 7mm screws with a PH1-screwdriver to loosen the fan.
  • Unplug the fan from the motherboard.

Unscrew the coiled springs indicated in red from the the motherboard.

Remove the 7mm screws with a PH1-screwdriver to loosen the fan.

Unplug the fan from the motherboard.

Step 10

  • Lift the fan out and then lift out the black grill covering the processor.

Lift the fan out and then lift out the black grill covering the processor.

Step 11

  • Use a Flathead screwdriver to turn the screw 180 degrees to unlock the processor from the motherboard.
  • Gently and vertically lift the processor out.
  • When placing the processor chip back in, make sure the golden triangle is on the top-left corner of the motherboard slot.
  • Be careful not to bend the pins on the processor chip. Broken pins will render the chip useless.

Use a Flathead screwdriver to turn the screw 180 degrees to unlock the processor from the motherboard.

Gently and vertically lift the processor out.

When placing the processor chip back in, make sure the golden triangle is on the top-left corner of the motherboard slot.

Be careful not to bend the pins on the processor chip. Broken pins will render the chip useless.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Matt McBride

Member since: 02/02/2017

827 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team 16-6, Blackwell Spring 2017                        

                                                  Member of USF Tampa, Team 16-6, Blackwell Spring 2017 



                    USFT-BLACKWELL-S17S16G6                     


                                            3 Members                     


                                            6 Guides authored