Difficulty
Moderate
Steps
7
Time Required
3 - 5 minutes
Sections
2
- Display
- 5 steps
- NFC Antenna
- 2 steps
Flags
0
BackHP ElitePad 1000 G2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display
- Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.
- Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.
Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.
Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.
1024
Step 2
- Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.
- Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.
- Pull on the suction cup while using the prying tool to separate the display from the tablet.
- Gently lift the display from the tablet in order to avoid damaging the cables.
Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.
Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.
Pull on the suction cup while using the prying tool to separate the display from the tablet.
Gently lift the display from the tablet in order to avoid damaging the cables.
Step 3
- To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.
- Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.
To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.
Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.
Step 4
- Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.
Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.
Step 5
- Remove the display from the tablet.
Remove the display from the tablet.
Step 6
NFC Antenna
- Locate the NFC antenna.
- Release the ZIF connector to which the NFC antenna cable is attached.
- To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.
Locate the NFC antenna.
Release the ZIF connector to which the NFC antenna cable is attached.
To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.
Step 7
- Detach the NFC antenna from the surface of the system board.
- The NFC antenna is attached to the system board with double-sided adhesive.
- Remove the NFC antenna.
Detach the NFC antenna from the surface of the system board.
The NFC antenna is attached to the system board with double-sided adhesive.
Remove the NFC antenna.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Jonathan Beasey
Member since: 07/09/2019
256 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019
Member of Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019
ERAU-WATKINS-SU19S3G2
4 Members
6 Guides authored