Difficulty
Moderate
Steps
7
Time Required
15 - 30 minutes
Sections
3
- Back Cover
- 4 steps
- Battery Cable
- 1 step
- Battery
- 2 steps
Flags
0
BackHP EliteBook 830 x360 G6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
For your safety, discharge the battery below 25% before disassembling your device. This reduces the risk of fire if the battery is accidentally damaged during the repair. If your battery is swollen, take appropriate precautions.
What you need
Step 1
Unfasten the back cover
- For your safety, discharge the battery below 25% and power down your device before disassembly.
- Use a Torx T5 screwdriver to loosen the five captive screws holding the back cover.
For your safety, discharge the battery below 25% and power down your device before disassembly.
Use a Torx T5 screwdriver to loosen the five captive screws holding the back cover.
1024
Step 2
Release the clips
- Insert an opening pick between a corner of the back corner and the chassis, near a hinge.
- Pry upward to release the retaining clips.
- These clips will make an audible click when they release.
- Repeat this process for the opposite corner.
Insert an opening pick between a corner of the back corner and the chassis, near a hinge.
Pry upward to release the retaining clips.
These clips will make an audible click when they release.
Repeat this process for the opposite corner.
Step 3
Release the remaining clips
- Insert your opening pick between the back cover and chassis, along the edge of the cover between the hinges.
- Pry up to release the additional retaining clips.
Insert your opening pick between the back cover and chassis, along the edge of the cover between the hinges.
Pry up to release the additional retaining clips.
Step 4
Remove the back cover
- Grab the cover by the corners next to the hinges.
- Swing the cover open and away from you.
- If the back cover feels stuck to the chassis, use an opening pick to release remaining clips around the perimeter of the back cover.
- Lift and remove the back cover from the laptop body.
Grab the cover by the corners next to the hinges.
Swing the cover open and away from you.
If the back cover feels stuck to the chassis, use an opening pick to release remaining clips around the perimeter of the back cover.
Lift and remove the back cover from the laptop body.
Step 5
Disconnect the battery
- Use the point of a spudger to push the sides of the battery connector out of its socket.
- Push on alternate sides to “walk” the connector out.
Use the point of a spudger to push the sides of the battery connector out of its socket.
Push on alternate sides to “walk” the connector out.
Step 6
Unfasten the battery
- Use your Phillips screwdriver to remove the five 4.2 mm-long screws securing the battery.
Use your Phillips screwdriver to remove the five 4.2 mm-long screws securing the battery.
Step 7
Remove the battery
- Pull the battery out from the retaining tabs at the front of the chassis.
- Remove the battery.
Pull the battery out from the retaining tabs at the front of the chassis.
Remove the battery.
To reassemble your device, follow these instructions in reverse order.
For optimal performance, calibrate your newly installed battery after completing this guide.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our HP EliteBook community for help.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Clay Eickemeyer
Member since: 09/19/2022
14,946 Reputation
125 Guides authored
Badges:
27
+24 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored
