Hp Elitebook 820 G1 Monitor Display Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          1 hour

Sections

Battery
4 steps
Fan
12 steps
Monitor display
3 steps

Flags

BackHP Elitebook 820 G1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.
Turn over laptop so that the bottom is showing.
Unlock the latch.

Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.

Turn over laptop so that the bottom is showing.

Unlock the latch.

1024

Step 2

Remove the back cover and you will then be able to see the battery.

Remove the back cover and you will then be able to see the battery.

Step 3

Unlatch the two latches securing the battery in the case.

Unlatch the two latches securing the battery in the case.

Step 4

Use a plastic opening tool to lift and remove the battery.

Use a plastic opening tool to lift and remove the battery.

Step 5

Fan

Remove the hard drive by unscrewing the four 8mm screws with the T7 philip’s head.

Remove the hard drive by unscrewing the four 8mm screws with the T7 philip’s head.

Step 6

Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.
Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.

Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.

Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.

Step 7

Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.
Remove SD card cap by just sliding out to reveal one screw.

Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.

Remove SD card cap by just sliding out to reveal one screw.

Step 8

Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.
Remove the 4mm SD card screw using the J00 tip.

Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.

Remove the 4mm SD card screw using the J00 tip.

Step 9

Remove the one 4mm fan screw using the J00 tip screwdriver.
Remove screw and metal plate to expose ribbon cable connector.

Remove the one 4mm fan screw using the J00 tip screwdriver.

Remove screw and metal plate to expose ribbon cable connector.

Step 10

Use an opening tool to pry up the ribbon connector to disconnect.

Use an opening tool to pry up the ribbon connector to disconnect.

Step 11

Turn laptop over back to normal position as shown in the image.
Use opening tools to pry up keyboard.
When prying up keyboard, be sure to start near any corner of the keyboard.
There are two ribbon cables that must be disconnected before fully removing keyboard.

Turn laptop over back to normal position as shown in the image.

Use opening tools to pry up keyboard.

When prying up keyboard, be sure to start near any corner of the keyboard.

There are two ribbon cables that must be disconnected before fully removing keyboard.

Step 12

Carefully lift keyboard on one side to expose the two ribbon cables.
Use an opening tool to lift up the locking clip and unplug the two ribbon cables.

Carefully lift keyboard on one side to expose the two ribbon cables.

Use an opening tool to lift up the locking clip and unplug the two ribbon cables.

Step 13

Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.

Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.

Step 14

Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.
The display is connected to the shell of the laptop.

Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.

The display is connected to the shell of the laptop.

Step 15

Unplug fan cable by pulling away from its connector.

Unplug fan cable by pulling away from its connector.

Step 16

Unscrew the two 6mm fan screws using the J00 tip.
Fan screws are encased in springs and cannot be removed.

Unscrew the two 6mm fan screws using the J00 tip.

Fan screws are encased in springs and cannot be removed.

Step 17

              Monitor display

Retrieve the monitor display connected to the plastic chassis.

Retrieve the monitor display connected to the plastic chassis.

Step 18

Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.

Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.

Step 19

Unhinge the monitor display from the chassis.

Unhinge the monitor display from the chassis.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Alberto Carlos Perez

Member since: 02/14/2018

365 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team S5-G1, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S5-G1, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S5G1                     


                                            3 Members                     


                                            7 Guides authored

richard P - Jun 18, 2022

Hello,

I need to replace the inverter as my screen is too much dark.

I cannot see the inverter and even I cannot find any inverter for this model.

Do you know how to access to this inverter? Is it embedded within the screen?

Thanks by advance.

Introduction#

What you need#

Team#

Introduction

What you need

Team