Hp Elitebook 1050 G1 Keyboard Panel Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

Motherboard
8 steps
Keyboard Panel
3 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackHP EliteBook 1050 G1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Motherboard

Remove the two 5.5mm screws with a Torx T8 driver.
Remove the five 8.7mm screws with a Torx T8 driver.
Remove the two 6.6mm screws with a Torx T8 driver.
Pry open the backplate with a Jimmy.

Remove the two 5.5mm screws with a Torx T8 driver.

Remove the five 8.7mm screws with a Torx T8 driver.

Remove the two 6.6mm screws with a Torx T8 driver.

Pry open the backplate with a Jimmy.

1024

Step 2

Remove the two 1.9mm screws from the SSDs with a Phillips #0 driver.
Disconnect the two PCIe SSDs by sliding them out of each port.

Remove the two 1.9mm screws from the SSDs with a Phillips #0 driver.

Disconnect the two PCIe SSDs by sliding them out of each port.

Step 3

Pull the clips on either side of the RAM chip away from each other using your fingers.
As you pry apart the clips, the RAM should pop up to rest at an angle to the motherboard.
Slide the RAM chips out of their respective slots.

Pull the clips on either side of the RAM chip away from each other using your fingers.

As you pry apart the clips, the RAM should pop up to rest at an angle to the motherboard.

Slide the RAM chips out of their respective slots.

Step 4

Remove eight 4.5 mm screws from the battery with a Phillips #1 screwdriver.
Disconnect the white tipped battery cable from the motherboard.

Remove eight 4.5 mm screws from the battery with a Phillips #1 screwdriver.

Disconnect the white tipped battery cable from the motherboard.

Step 5

Remove the six 4.5mm screws from the fan assembly using a Phillips #00 screwdriver.
Unscrew four 3.6mm screws from the heatsink assembly with a Phillips #00 screwdriver.
These “captive” screws are connected to the heatsink and will not detach from it.
Remove the fan assembly.

Remove the six 4.5mm screws from the fan assembly using a Phillips #00 screwdriver.

Unscrew four 3.6mm screws from the heatsink assembly with a Phillips #00 screwdriver.

These “captive” screws are connected to the heatsink and will not detach from it.

Remove the fan assembly.

Step 6

Unplug the seven ZIF connecters from the motherboard by flipping up the black switches with a spudger and pulling out the cables.

Unplug the seven ZIF connecters from the motherboard by flipping up the black switches with a spudger and pulling out the cables.

Step 7

Remove two 1.9mm screws from the display cable bracket using a Phillips #00 driver.
Remove the two connectors on the right side gently.
Remove the connector on right side of motherboard.
Remove the three 4.5mm screws using a Phillips #00 driver and remove the bracket.
Remove the two coaxial cables.

Remove two 1.9mm screws from the display cable bracket using a Phillips #00 driver.

Remove the two connectors on the right side gently.

Remove the connector on right side of motherboard.

Remove the three 4.5mm screws using a Phillips #00 driver and remove the bracket.

Remove the two coaxial cables.

Step 8

Remove the two 3mm screws using a Phillips #00 driver.
Remove the motherboard by lifting it up and out of the case.

Remove the two 3mm screws using a Phillips #00 driver.

Remove the motherboard by lifting it up and out of the case.

Step 9

              Keyboard Panel

Peel back the black cover on the keyboard.

Peel back the black cover on the keyboard.

Step 10

Remove all 52 screws from the keyboard panel using a Phillips #000 screwdriver.

Remove all 52 screws from the keyboard panel using a Phillips #000 screwdriver.

Step 11

Remove the keyboard panel from the laptop.

Remove the keyboard panel from the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Ming-chin Wu

Member since: 09/20/2021

193 Reputation

                                      2 Guides authored                  



                       Badges:
                       3

Team

                       The Citadel Military College of South Carolina, Team 1-3, Eggleston Fall 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team 1-3, Eggleston Fall 2021 



                    CMCSC-EGGLESTON-F21S1G3                     


                                            3 Members                     


                                            2 Guides authored

Better Introduction#

Introduction#

What you need#

Team#

Better Introduction

Introduction

What you need

Team