Hp Compaq Nc6400 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          30 minutes            

Sections

2

• Battery
• 4 steps
• Screen
• 9 steps

Flags

0

• BackHP Compaq nc6400

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Turn off and unplug laptop.

Turn off and unplug laptop.

1024

Step 2

• Locate the battery lock below the battery labeled one.
• Slide the lock all the way to the left to release the left lock of the battery.

Locate the battery lock below the battery labeled one.

Slide the lock all the way to the left to release the left lock of the battery.

Step 3

• Locate the lock labeled two at the bottom right corner below the battery.
• Slide and hold the lock to the left.

Locate the lock labeled two at the bottom right corner below the battery.

Slide and hold the lock to the left.

Step 4

• Once both the battery locks are unlocked, slide the battery out to remove.

Once both the battery locks are unlocked, slide the battery out to remove.

Step 5

              Screen               

• Remove the four 1.2mm Philips #1 screws attaching the plastic cover to the monitor.
• The screws may have a small, black plastic cover that lays flush with the screen. Remove these using a pointed tool such as the spudger or philips head screwdriver by prying them out.

Remove the four 1.2mm Philips #1 screws attaching the plastic cover to the monitor.

The screws may have a small, black plastic cover that lays flush with the screen. Remove these using a pointed tool such as the spudger or philips head screwdriver by prying them out.

Step 6

• Remove the four 1.2 Philips #1 screws attaching the face plate to the body.

Remove the four 1.2 Philips #1 screws attaching the face plate to the body.

Step 7

• Pry up the plastic screen cover using a pry tool.
• Keeping the pry tool under the trim, slide it around the entire screen until the the cover has completely detached from the base.
• You might need to slide the display clip on the top of the screen in order to fully remove the plastic cover.

Pry up the plastic screen cover using a pry tool.

Keeping the pry tool under the trim, slide it around the entire screen until the the cover has completely detached from the base.

You might need to slide the display clip on the top of the screen in order to fully remove the plastic cover.

Step 8

• Remove the two 1.2 Philips #1 screws holding down the sensor board at the bottom of the monitor.

Remove the two 1.2 Philips #1 screws holding down the sensor board at the bottom of the monitor.

Step 9

• Remove the right-most 1.2mm Philips #1 screw on the bottom of the monitor.

Remove the right-most 1.2mm Philips #1 screw on the bottom of the monitor.

Step 10

• Without lifting the bottom of the monitor, gently flip the screen and lay it face down on the keyboard.

Without lifting the bottom of the monitor, gently flip the screen and lay it face down on the keyboard.

Step 11

• Remove the tape holding down the video cable to the monitor.
• Gently pull out the video cable from the monitor.

Remove the tape holding down the video cable to the monitor.

Gently pull out the video cable from the monitor.

Step 12

• Remove the monitor’s power cable from the sensor board.
• This is the cable on the farthest right of the sensor board.

Remove the monitor’s power cable from the sensor board.

This is the cable on the farthest right of the sensor board.

Step 13

• Once all cables attaching the casing to the monitor have been disconnected, remove the entire screen from the computer and lay it on a flat surface.
• Remove the four 1.2 Philips #1 screws attaching the bezel to the right side of the monitor.
• Attach bezel to replacement screen.

Once all cables attaching the casing to the monitor have been disconnected, remove the entire screen from the computer and lay it on a flat surface.

Remove the four 1.2 Philips #1 screws attaching the bezel to the right side of the monitor.

Attach bezel to replacement screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Luis Vazquez                     

Member since: 09/24/2013

401 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Cal Poly, Team 14-6, Forte Fall 2013                        

                                                  Member of Cal Poly, Team 14-6, Forte Fall 2013 



                    CPSU-FORTE-F13S14G6                     


                                            5 Members                     


                                            5 Guides authored                     

Peter Q. - May 13, 2021

Reply

Nicely done. Thanks?