Difficulty
Moderate
Steps
12
Time Required
30 minutes
Sections
2
- Keyboard, Touchpad
- 5 steps
- Camera
- 7 steps
Flags
0
BackHP Chromebook 14-x013dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Keyboard, Touchpad
- Using the plastic spudger, gently lift the 5 rubber pads away from their seating.
Using the plastic spudger, gently lift the 5 rubber pads away from their seating.
1024
Step 2
- Remove the five 6mm screws located under the removed pads using Phillips #00 screwdriver.
Remove the five 6mm screws located under the removed pads using Phillips #00 screwdriver.
Step 3
- With the Phillips #00 screwdriver, remove the remaining eight 6mm screws. You will now have thirteen 6mm screws removed from the case.
With the Phillips #00 screwdriver, remove the remaining eight 6mm screws. You will now have thirteen 6mm screws removed from the case.
Step 4
- To continue removing the back cover, turn the laptop over as displayed.
- Use the plastic spudger to gently pry around the base of the laptop from the back cover. Continue prying around the entire base of the laptop.
To continue removing the back cover, turn the laptop over as displayed.
Use the plastic spudger to gently pry around the base of the laptop from the back cover. Continue prying around the entire base of the laptop.
Step 5
- Gently lift the silver base of the laptop from the bottom, but do not remove it.
- To remove the ribbon cables, lift the latch holding the ribbon cables in place and then pull them free.
- Remove the keyboard panel from the laptop.
Gently lift the silver base of the laptop from the bottom, but do not remove it.
To remove the ribbon cables, lift the latch holding the ribbon cables in place and then pull them free.
Remove the keyboard panel from the laptop.
Step 6
Camera
- Disconnect the black and white wires connected to the Wi-Fi module.
- Remove the wire from the casing.
Disconnect the black and white wires connected to the Wi-Fi module.
Remove the wire from the casing.
Step 7
- Pull the ribbon cable out of socket.
Pull the ribbon cable out of socket.
Step 8
- Use a Phillips #00 screwdriver to remove the two 6mm screws located at the upper left and right corners.
Use a Phillips #00 screwdriver to remove the two 6mm screws located at the upper left and right corners.
Step 9
- Remove the lid out of the laptop.
- It is helpful to rotate the lid to a 90-degree angle.
Remove the lid out of the laptop.
It is helpful to rotate the lid to a 90-degree angle.
Step 10
- Using the plastic opening tool, pry the left and right side of the top of the lid.
- It is not necessary to remove the entire frame, only pry the top to expose the camera.
Using the plastic opening tool, pry the left and right side of the top of the lid.
It is not necessary to remove the entire frame, only pry the top to expose the camera.
Step 11
- Using tweezers, gently remove the connection hold the camera in place.
Using tweezers, gently remove the connection hold the camera in place.
Step 12
- Gently pry the camera mount out of the lid.
- Lift the camera mount out of the lid.
Gently pry the camera mount out of the lid.
Lift the camera mount out of the lid.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Eile Woeltje
Member since: 11/06/2019
295 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
IUPUI, Team S1-G3, Stella Fall 2019
Member of IUPUI, Team S1-G3, Stella Fall 2019
IUPUI-STELLA-F19S1G3
3 Members
2 Guides authored
Douglas Walker - Sep 25, 2020
Reply
Thank you, very helpful. You could also just start at Step 10 without removing the display
