Difficulty
Moderate
Steps
8
Time Required
30 - 45 minutes
Sections
2
- Battery
- 6 steps
- Charging Port
- 2 steps
Flags
0
BackHP Chromebook 14-x010wm
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the thirteen 5.7mm screws from the back of the laptop using a Phillips #00 screwdriver.
- Remove rubber covers to reveal concealed screws, as needed.
Remove the thirteen 5.7mm screws from the back of the laptop using a Phillips #00 screwdriver.
Remove rubber covers to reveal concealed screws, as needed.
1024
Step 2
- Flip the laptop over carefully and open the cover.
- Use a plastic opening tool to pry open the front edge and along the sides of the keyboard cover to separate it from the computer’s base.
- Lift the keyboard cover from the computer’s base carefully.
Flip the laptop over carefully and open the cover.
Use a plastic opening tool to pry open the front edge and along the sides of the keyboard cover to separate it from the computer’s base.
Lift the keyboard cover from the computer’s base carefully.
Step 3
- Lifting the keyboard cover too much may damage the internal cables of the laptop.
- Lift the black plastic flap, using a plastic opening tool, of the zero insertion force (ZIF) connector that holds the keyboard cable in place.
- Disconnect the keyboard cable by slowly pulling it from the system board.
- Lift the black plastic flap that holds the battery cable in place using a plastic opening tool.
- Remove the battery cable by slowly pulling the plastic connector towards you.
- Remove carefully and set aside keyboard panel.
Lifting the keyboard cover too much may damage the internal cables of the laptop.
Lift the black plastic flap, using a plastic opening tool, of the zero insertion force (ZIF) connector that holds the keyboard cable in place.
Disconnect the keyboard cable by slowly pulling it from the system board.
Lift the black plastic flap that holds the battery cable in place using a plastic opening tool.
Remove the battery cable by slowly pulling the plastic connector towards you.
Remove carefully and set aside keyboard panel.
Step 4
- Flip the plastic flap holding the battery cable using a plastic opening tool.
- Disconnect the battery cable by carefully pulling it from the system board.
Flip the plastic flap holding the battery cable using a plastic opening tool.
Disconnect the battery cable by carefully pulling it from the system board.
Step 5
- Remove the seven M2xL3.0 screws from around the battery using a Phillips #00 screwdriver.
Remove the seven M2xL3.0 screws from around the battery using a Phillips #00 screwdriver.
Step 6
- Peel the wire band off of the battery carefully.
- Remove the battery by lifting slightly, then slowly pull it towards you.
Peel the wire band off of the battery carefully.
Remove the battery by lifting slightly, then slowly pull it towards you.
Step 7
Charging Port
- Use a plastic opening tool to undo the tabs securing the charging port.
- Then gently lift the port up and away from the laptop edge.
Use a plastic opening tool to undo the tabs securing the charging port.
Then gently lift the port up and away from the laptop edge.
Step 8
- Use a plastic opening tool to pry both ends of the corresponding white plug from it’s port at the motherboard.
- Carefully pull the plug out of the port.
Use a plastic opening tool to pry both ends of the corresponding white plug from it’s port at the motherboard.
Carefully pull the plug out of the port.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Rachel Clevidence
Member since: 04/04/2019
85 Reputation
1 Guide authored
Badges:
3
Team
IUPUI, Team S3-G3, Harley Spring 2019
Member of IUPUI, Team S3-G3, Harley Spring 2019
IUPUI-HARLEY-S19S3G3
3 Members
2 Guides authored
