Difficulty

Moderate

Steps

8

Time Required

                          20 minutes

Sections

3

  • Keyboard
  • 3 steps
  • Battery
  • 3 steps
  • Fan
  • 2 steps

Flags

0

  • BackHP Chromebook 14-q029wm

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard
  • Remove nine 5mm Phillips #0 screws from the back case.
  • Remove the rubber caps using a spudger.
  • Remove the four remaining 5mm Phillips #0 screws.

Remove nine 5mm Phillips #0 screws from the back case.

Remove the rubber caps using a spudger.

Remove the four remaining 5mm Phillips #0 screws.

1024

Step 2

  • Use an opening tool to unclip the bottom plastic covering of the laptop.
  • Go around the sides of the laptop until the bottom unclips completely and comes off of the laptop.
  • Be careful not to break the plastic clips.

Use an opening tool to unclip the bottom plastic covering of the laptop.

Go around the sides of the laptop until the bottom unclips completely and comes off of the laptop.

Be careful not to break the plastic clips.

Step 3

  • Once the bottom is completely unclipped, remove the covering slowly so you do not pull and rip the wires.
  • There is a little black lever that you have to pull in order to remove the wires. They are found on top of where the wires are connected.
  • Remove the larger wire first.
  • Then remove the smaller wire.
  • It is better to use a pair of tweezers for accuracy
  • From there the keyboard should completely come off.

Once the bottom is completely unclipped, remove the covering slowly so you do not pull and rip the wires.

There is a little black lever that you have to pull in order to remove the wires. They are found on top of where the wires are connected.

Remove the larger wire first.

Then remove the smaller wire.

It is better to use a pair of tweezers for accuracy

From there the keyboard should completely come off.

Step 4

              Battery
  • Use your fingers to pull the white tab out of the black slot above the battery.

Use your fingers to pull the white tab out of the black slot above the battery.

Step 5

  • Remove the 3mm Phillips #0 screws.

Remove the 3mm Phillips #0 screws.

Step 6

  • Pick up and gently remove the battery.

Pick up and gently remove the battery.

Step 7

              Fan
  • Remove the three 3mm Phillips #0 screws.
  • The bottom right screw may be covered by the fan’s wires.

Remove the three 3mm Phillips #0 screws.

The bottom right screw may be covered by the fan’s wires.

Step 8

  • Using your fingers or an opening tool, remove the cable connecting the fan to the motherboard.
  • Gently remove the fan.

Using your fingers or an opening tool, remove the cable connecting the fan to the motherboard.

Gently remove the fan.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Andrew Pratt

Member since: 11/05/2019

654 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UMass Dartmouth, Team S1-G5, Barthe Fall 2019                        

                                                  Member of UMass Dartmouth, Team S1-G5, Barthe Fall 2019 



                    UMASSD-BARTHE-F19S1G5                     


                                            3 Members                     


                                            5 Guides authored