Difficulty
Moderate
Steps
8
Time Required
25 minutes
Sections
1
- SD Card Reader
- 8 steps
Flags
0
BackHP Chromebook 11-2210nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SD Card Reader
- Turn over your laptop and remove the 9 visible 6mm screws using the Phillips #1 screwdriver.
Turn over your laptop and remove the 9 visible 6mm screws using the Phillips #1 screwdriver.
1024
Step 2
- Using the metal spudger, remove the two rubber pads that are closer to the hinge of the laptop.
- Remove the two additional 6mm screws located beneath the rubber pads using the Phillips #1 screwdriver.
- The two bottom rubber pads do not contain screws, but you may check if you wish to be sure.
Using the metal spudger, remove the two rubber pads that are closer to the hinge of the laptop.
Remove the two additional 6mm screws located beneath the rubber pads using the Phillips #1 screwdriver.
The two bottom rubber pads do not contain screws, but you may check if you wish to be sure.
Step 3
- Turn the Laptop over and with the metal spudger start to run it along the plastic seam to pry it off.
- You will hear popping sounds when you are sliding the spudger along the device.
- For an easier removal, start from the sides and work your way in to the corners.
Turn the Laptop over and with the metal spudger start to run it along the plastic seam to pry it off.
You will hear popping sounds when you are sliding the spudger along the device.
For an easier removal, start from the sides and work your way in to the corners.
Step 4
- Carefully lift off the keyboard and gently place it towards you until the two ribbon wires become visible and place the keyboard down.
- Locate where the two ribbon wires are being held in place by two chips.
- This does not disconnect the keyboard from the laptop just yet.
Carefully lift off the keyboard and gently place it towards you until the two ribbon wires become visible and place the keyboard down.
Locate where the two ribbon wires are being held in place by two chips.
This does not disconnect the keyboard from the laptop just yet.
Step 5
- Using the nylon spudger, push the plastic clasps holding the two ribbon wires up to properly disconnect the wires.
- You must use the nylon spudger for this step. Any metal can damage your motherboard.
- This step completely disconnects the keyboard to allow safe removal and replacement.
Using the nylon spudger, push the plastic clasps holding the two ribbon wires up to properly disconnect the wires.
You must use the nylon spudger for this step. Any metal can damage your motherboard.
This step completely disconnects the keyboard to allow safe removal and replacement.
Step 6
- Locate the SD card reader at the top left corner above the battery.
- Flip up the plastic clasps holding the ZIF connectors into place by using the nylon spudger or your finger.
- Gently slide out the ribbon cable, removing it from the SD Card Reader.
Locate the SD card reader at the top left corner above the battery.
Flip up the plastic clasps holding the ZIF connectors into place by using the nylon spudger or your finger.
Gently slide out the ribbon cable, removing it from the SD Card Reader.
Step 7
- Remove the two 4mm screws using a Phillips #1 screwdriver.
- This successfully disconnects the SD port from the laptop.
Remove the two 4mm screws using a Phillips #1 screwdriver.
This successfully disconnects the SD port from the laptop.
Step 8
- Gently lift and remove SD Card Reader component from laptop.
Gently lift and remove SD Card Reader component from laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Gerardo Cardona
Member since: 10/02/2018
364 Reputation
2 Guides authored
Badges:
3
Team
Sam Houston State, Team S11-G3, Blackburne Fall 2018
Member of Sam Houston State, Team S11-G3, Blackburne Fall 2018
SHSU-BLACKBURNE-F18S11G3
4 Members
5 Guides authored
