Hp 15 Dy2024Nr Hard Drive Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 10 minutes

Sections

Back Cover
3 steps
Battery
2 steps
Hard Drive
2 steps

Flags

BackHP 15-dy2024nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

When removing the hard drive, be sure to save your files to another so that you do not lose them. If your hard drive is corrupted, you may be able to save your files by following a guide, or taking it to a professional.

When removing any chip or board from your laptop, be careful to touch the sides only. Touching any of the components can damage them. Before removing or replacing any part, be sure the laptop is powered off. If you are unsure, turn the laptop on, then shut it off from the start menu.

What you need

Step 1

              Back Cover

Use the Halberd spudger to peel one corner of each of the rubber feet from the bottom of the laptop.
Gently peel the feet from the laptop revealing the screws underneath.
If the rubber foot peels away but leaves adhesive behind you must peel the adhesive away before removing the screws.

Use the Halberd spudger to peel one corner of each of the rubber feet from the bottom of the laptop.

Gently peel the feet from the laptop revealing the screws underneath.

If the rubber foot peels away but leaves adhesive behind you must peel the adhesive away before removing the screws.

1024

Step 2

Use a Phillips #1 screwdriver to remove:
Two 2.5mm x 6mm screws
Six 2mm x 6mm screws
Be sure to keep different screw sizes separated.

Use a Phillips #1 screwdriver to remove:

Two 2.5mm x 6mm screws

Six 2mm x 6mm screws

Be sure to keep different screw sizes separated.

Step 3

Insert an iFixit opening tool into the seam between the keyboard area and bottom cover.
Using another iFixit opening tool, slide along the seam to unhook the clips.
There are clips all the way around the seam. You may hear a popping sound as the clips come loose. This step may require some force to separate the back cover from the laptop.
When the front of the laptop is open, you can use your finger to hold a corner open then slide an iFixit opening tool along the seam toward the back corner.
After the clips have been released, flip the laptop over and lift the cover.

Insert an iFixit opening tool into the seam between the keyboard area and bottom cover.

Using another iFixit opening tool, slide along the seam to unhook the clips.

There are clips all the way around the seam. You may hear a popping sound as the clips come loose. This step may require some force to separate the back cover from the laptop.

When the front of the laptop is open, you can use your finger to hold a corner open then slide an iFixit opening tool along the seam toward the back corner.

After the clips have been released, flip the laptop over and lift the cover.

Step 4

              Battery

Remove five 2.0mm x 3.0mm screws using a Phillips #00 screwdriver.
Use the iFixit opening picks to lift the battery away from the laptop.

Remove five 2.0mm x 3.0mm screws using a Phillips #00 screwdriver.

Use the iFixit opening picks to lift the battery away from the laptop.

Step 5

Be aware that the battery is plugged into the motherboard.
Unplug the battery from the motherboard.
Lift the battery away from the laptop and remove.

Be aware that the battery is plugged into the motherboard.

Unplug the battery from the motherboard.

Lift the battery away from the laptop and remove.

Step 6

              Hard Drive

Remove the single 2 mm screw from the hard drive using a Phillips #00 screwdriver.

Remove the single 2 mm screw from the hard drive using a Phillips #00 screwdriver.

Step 7

Pull the SSD away from the connector, while gently lifting it out using your hands.

Pull the SSD away from the connector, while gently lifting it out using your hands.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Konnor Young

Member since: 09/27/2022

437 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Utah Tech University, Team 1-4, McMurrin Fall 2022                        

                                                  Member of Utah Tech University, Team 1-4, McMurrin Fall 2022 



                    UTAHTECH-MCMURRIN-F22S1G4                     


                                            3 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team