Difficulty
Moderate
Steps
6
Time Required
Suggest a time??
Sections
1
- How to seal with DeLonghi ESAM xxxx - the brewing group
- 6 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackDeLonghi ESAM family of coffee preparing automates
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
How to seal with DeLonghi ESAM xxxx - the brewing group
- Press the two red buttons of the brew group together and remove the brew group.
Press the two red buttons of the brew group together and remove the brew group.
1024
Step 2
- Lay the machine on its rearside, with the open frontside looking upwards.
- The brewing strainer of the upper piston is fixed with two phillips screws PH2.Turn it out.
- With some force, remove the brewing strainer and remove the old sealing ring.
- Clean the brewing strainer and what is underneath is fine.
- Grease the new sealing ring with food grade silicone grease. Put it on the piston and tighten the brewing sieve again.
Lay the machine on its rearside, with the open frontside looking upwards.
The brewing strainer of the upper piston is fixed with two phillips screws PH2.Turn it out.
With some force, remove the brewing strainer and remove the old sealing ring.
Clean the brewing strainer and what is underneath is fine.
Grease the new sealing ring with food grade silicone grease. Put it on the piston and tighten the brewing sieve again.
Step 3
- Pull the plastic retaining clip off the moving base of the brew group. It is just plugged.
- Pull the bottom out of the black plastic piece.
Pull the plastic retaining clip off the moving base of the brew group. It is just plugged.
Pull the bottom out of the black plastic piece.
Step 4
- Press out the piston on the opposite side.
- Remove the two sealing rings.
Press out the piston on the opposite side.
Remove the two sealing rings.
Step 5
- The filter screen is attached with a phillips screw PH2. Turn it out. Take off the brewing sieve.
- Clean brewing strainer and what is behind it is good.
The filter screen is attached with a phillips screw PH2. Turn it out. Take off the brewing sieve.
Clean brewing strainer and what is behind it is good.
Step 6
- The crema valve is hard to recognize. It is covered with a plastic stopper. You can gently remove it with the sharp tip of a cutter.
- He is very tight. Hoist piece by piece high with the cutter tip.
- Underneath is the valve. It consists of a spring and a small piston. Clean everything very well, also the channels. Be very careful.
- Plug in the valve again. Screw the brewing strainer tight and attach the two new sealing rings. Grease the sealing rings and the piston barrel thinly with food-grade silicone grease.
The crema valve is hard to recognize. It is covered with a plastic stopper. You can gently remove it with the sharp tip of a cutter.
He is very tight. Hoist piece by piece high with the cutter tip.
Underneath is the valve. It consists of a spring and a small piston. Clean everything very well, also the channels. Be very careful.
Plug in the valve again. Screw the brewing strainer tight and attach the two new sealing rings. Grease the sealing rings and the piston barrel thinly with food-grade silicone grease.
Repeat the steps in order to reassemble your device.
Cancel: I did not complete this guide.
4 other people completed this guide.
These translators are helping us fix the world! Want to contribute? Start translating ›
Special thanks to these translators:
100%
irlanda
VauWeh
Author
with 1 other contributor
VauWeh
Member since: 10/19/2015
160,441 Reputation
210 Guides authored
Badges:
41
+38 more badges
