How To Restring A Badminton Racquet Repair Guide

Difficulty

Moderate

Steps

Time Required

                          45 minutes - 1 hour

Sections

How to Restring a Badminton Racquet
13 steps

Flags

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

BackSporting Goods
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Recreational badminton players can get back on the court without spending money on a new racquet or professional restringing services.

What you need

Step 1

              How to Restring a Badminton Racquet

Insert one end of the string through the hole at the bottom of the racquet closest to the shaft and drag it straight up to the corresponding hole at the top of the raquet.

Insert one end of the string through the hole at the bottom of the racquet closest to the shaft and drag it straight up to the corresponding hole at the top of the raquet.

1024

Step 2

Loop the string through the top two holes and drag it back down to the hole on the opposite side of the shaft you started from.
Make sure the excess string is evenly divided so that each side has the same amount.

Loop the string through the top two holes and drag it back down to the hole on the opposite side of the shaft you started from.

Make sure the excess string is evenly divided so that each side has the same amount.

Step 3

Continue to string straight up and down one side of the racquet until you reach the area of the racquet that naturally begins to curve.

Continue to string straight up and down one side of the racquet until you reach the area of the racquet that naturally begins to curve.

Step 4

When you’re done stringing, there should be some leftover string at the top.
If there is not enough to properly tie off, pull on the strands in order to create slack in the line.

When you’re done stringing, there should be some leftover string at the top.

If there is not enough to properly tie off, pull on the strands in order to create slack in the line.

Step 5

Use your fingers to make a knot (you may need to make two knots on top of each other so the string can’t slide back through the hole).
Pull on each strand, beginning with the outermost strand with the knot, and move towards the middle so that the string tightens up and becomes taut.

Use your fingers to make a knot (you may need to make two knots on top of each other so the string can’t slide back through the hole).

Pull on each strand, beginning with the outermost strand with the knot, and move towards the middle so that the string tightens up and becomes taut.

Step 6

Perform the same steps of stringing on the other side of the racquet and make a knot at the top. Make sure to pull very tightly to reduce slack in the string and create the knot as close to the hole in the racquet as possible.
Use the pliers to help hold the strings taught while tying the second knot. The pliers can also be used to slide the knot closer to the hole in the racquet if you have trouble making a small, close knot with your fingers.

Perform the same steps of stringing on the other side of the racquet and make a knot at the top. Make sure to pull very tightly to reduce slack in the string and create the knot as close to the hole in the racquet as possible.

Use the pliers to help hold the strings taught while tying the second knot. The pliers can also be used to slide the knot closer to the hole in the racquet if you have trouble making a small, close knot with your fingers.

Step 7

To begin the horizontal stringing, tie the second string onto the racquet frame. Start at the fourth hole over from the base and make a knot with your fingers on the inside of the frame.
Loop the string back inwards through the seventh hole from the base.

To begin the horizontal stringing, tie the second string onto the racquet frame. Start at the fourth hole over from the base and make a knot with your fingers on the inside of the frame.

Loop the string back inwards through the seventh hole from the base.

Step 8

When stringing the horizontal strands, you must weave over and under each vertical strand with the new string while continuing to pull the string tight.

When stringing the horizontal strands, you must weave over and under each vertical strand with the new string while continuing to pull the string tight.

Step 9

Thread the horizontal strand straight across and through the hole opposite the one you started at. Loop back into the next hole up the side of the racquet.
For the second row, string under-over instead of over-under so that the horizontal strands alternate being on top of or underneath each vertical strand.

Thread the horizontal strand straight across and through the hole opposite the one you started at. Loop back into the next hole up the side of the racquet.

For the second row, string under-over instead of over-under so that the horizontal strands alternate being on top of or underneath each vertical strand.

Step 10

With each additional row you string up the racquet, switch from over-under to under-over so that every other horizontal string follows the same pattern.
A weave pattern should start to form and your racquet should begin to resemble the image.

With each additional row you string up the racquet, switch from over-under to under-over so that every other horizontal string follows the same pattern.

A weave pattern should start to form and your racquet should begin to resemble the image.

Step 11

At the end of the strand (right when the racquet naturally begins to curve), pull the strings tight. You may need to pull on each strand from the base up to get rid of any slack in the string. Make sure the tension in the strings is very high and there is little give when you push down on the strings with your hand.
Tie a knot in the string on the outside of the racquet. Make the knot very close to the racquet for best tension, pliers can help slide the knot down to the frame. More than one knot may be necessary to prevent the string from sliding back through the hole.

At the end of the strand (right when the racquet naturally begins to curve), pull the strings tight. You may need to pull on each strand from the base up to get rid of any slack in the string. Make sure the tension in the strings is very high and there is little give when you push down on the strings with your hand.

Tie a knot in the string on the outside of the racquet. Make the knot very close to the racquet for best tension, pliers can help slide the knot down to the frame. More than one knot may be necessary to prevent the string from sliding back through the hole.

Step 12

Cut off all the excess string, leaving some space after the knots.

Cut off all the excess string, leaving some space after the knots.

Step 13

Your final product is ready. The strings should not move much when you gently push down on them with your hand.
If they are loose, consider tightening the strings by pulling out slack strand by strand before retying a knot.

Your final product is ready. The strings should not move much when you gently push down on them with your hand.

If they are loose, consider tightening the strings by pulling out slack strand by strand before retying a knot.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 4 other contributors

                    Sabina

Member since: 09/19/2018

406 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of Minnesota, Team S1-G1, Card Fall 2018                        

                                                  Member of University of Minnesota, Team S1-G1, Card Fall 2018 



                    UMN-CARD-F18S1G1                     


                                            3 Members                     


                                            1 Guide authored

Deepak Chaudhari - Jun 11, 2019

Very Simple and easily understandable guideline.

I request Sabina to please include guidelines on automatic stringing Badminton machine(Siboasi)with steps and images.

If possible please send me on my email address(dvc870621@gmail.com).

Thanks

Deepak Chaudhari

Michael Lin - Aug 9, 2021

Would only recommend this method for very cheap rackets, but at that price point, it is very possible that the cost of the string will exceed the price of a new racket.

Never tie off the on the outside of the racket as this leads to increased stress on the frame.

Featured Student Guide#

Introduction#

What you need#

Team#

Featured Student Guide

Introduction

What you need

Team