Difficulty
Moderate
Steps
11
Time Required
Suggest a time??
Sections
1
- Outer Sole
- 11 steps
Flags
0
BackShoe
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The use of basic hand tools is required.
What you need
Step 1
Outer Sole
- Cut across the tire using a knife creating a groove approximately the width of the tread.
- Do not cut completely through the tire.
Cut across the tire using a knife creating a groove approximately the width of the tread.
Do not cut completely through the tire.
1024
Step 2
- Remove the tread from the tire while scraping underneath the top layer with a knife.
- Peel back the layer, cut the tread, and remove it from the tire.
Remove the tread from the tire while scraping underneath the top layer with a knife.
Peel back the layer, cut the tread, and remove it from the tire.
Step 3
- Lay the tire tread flat.
- External side of tread facing down on the table.
Lay the tire tread flat.
External side of tread facing down on the table.
Step 4
- Clean the bottom of the sandal with a damp cloth to ensure the surface is free of debris.
Clean the bottom of the sandal with a damp cloth to ensure the surface is free of debris.
Step 5
- Place the sandal with the sole facing down on the tire tread.
Place the sandal with the sole facing down on the tire tread.
Step 6
- Outline the sandal with a bright colored marker.
- Remove the sandal.
Outline the sandal with a bright colored marker.
Remove the sandal.
Step 7
- Apply adhesive on the inside of the marker drawn.
Apply adhesive on the inside of the marker drawn.
Step 8
- Place the sandal in the outline.
Place the sandal in the outline.
Step 9
- Insert a wood block into the sandal.
- Clamp the wood block to the tire tread.
- Allow adhesive to cure according to manufacturer recommendations.
Insert a wood block into the sandal.
Clamp the wood block to the tire tread.
Allow adhesive to cure according to manufacturer recommendations.
Step 10
- Remove the clamps and wood block.
- Cut the excess tread from the sandal with a utility knife.
- Never cut toward yourself.
Remove the clamps and wood block.
Cut the excess tread from the sandal with a utility knife.
Never cut toward yourself.
Step 11
- Smooth edges of the tread, and remove excess tread/adhesive.
Smooth edges of the tread, and remove excess tread/adhesive.
Your shoes are now ready to wear.
Cancel: I did not complete this guide.
17 other people completed this guide.
Author
with 8 other contributors
Ronan
Member since: 06/24/2015
190 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Colorado Springs, Team 1-3, Mcmichael SU 2015
Member of Colorado Springs, Team 1-3, Mcmichael SU 2015
UCCS-MCMICHAEL-SU15S1G3
3 Members
1 Guide authored
Ranjie - Feb 8, 2017
Reply
can I use this on heavy duty shoes like basketball shoes for outdoors?
Andy - Mar 20, 2017
Reply
What type of glue did you use? I am wanting to fix the soles of my Chaco sandals as the sole is coming apart. If you could give me the best brand I would appreciate it.
Andy
Rick - Jul 21, 2017
I was just going to post about fixing Chacos!! To answer your question, I use Barge Cement: it’s a’contact cement’ so paint both faces with it smoothly, wait about 5 to 15 mins to let it get real tacky then clamp it! I always let this and similar cure for 24 hours, if not 48.
My problem with (two pair) of Chacos is extremely quick wear. I don’t get the popularity if I get a half of summer before the heel is worn down to the sandal body.
Ron Hargrove - Mar 25, 2017
Reply
These instructions used what appears to be silicone glue, which will not hold up. What would be much better is contact cement. Barge All Purpose TF cement would be much better. I would also use a rasp or a small sanding disk to try and smooth the rubber before gluing it down as well.
James Stork - Jan 25, 2020
Reply
I used the tread from a lawn tractor tire as it has no steel cords to worry about. It was easy to cut. I ground the inner texture off the tire and abraded it with a sanding disk and glued it on with contact cement. One year later and still going.