How To Replace A Rear Brake Cable Repair Guide

Difficulty

Easy

Steps

Time Required

                          30 minutes

Sections

Rear Brake Cable
10 steps

Flags

BackBicycles
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Brake Cable

Using the smart wrench and socket wrench, remove the nuts that are holding the connector to the old brake line.
After taking apart the connector, slide the screw off the brake line.
The nut may be difficult to remove if it has not been removed for a while.
Keep in mind the order the parts came off the connector. This will make reassembly easier.

Using the smart wrench and socket wrench, remove the nuts that are holding the connector to the old brake line.

After taking apart the connector, slide the screw off the brake line.

The nut may be difficult to remove if it has not been removed for a while.

Keep in mind the order the parts came off the connector. This will make reassembly easier.

1024

Step 2

Remove the cable housing from its holders.
Slide the housing off the brake cable.

Remove the cable housing from its holders.

Slide the housing off the brake cable.

Step 3

Remove the second cable housing from its holder.
Unscrew the other end of the housing from the brake.
Remove the housing from the cable.

Remove the second cable housing from its holder.

Unscrew the other end of the housing from the brake.

Remove the housing from the cable.

Step 4

Apply pressure to the brake to reveal the end of the brake cable.
Remove the cable from its holder within the brake.
Pull the remaining cable through the brake.

Apply pressure to the brake to reveal the end of the brake cable.

Remove the cable from its holder within the brake.

Pull the remaining cable through the brake.

Step 5

Flip your bike to make the brake housing more visible.
Insert the new brake cable into the brake housing.

Flip your bike to make the brake housing more visible.

Insert the new brake cable into the brake housing.

Step 6

Slide the cable housing onto the new cable.
Re-insert the housing back into its holders.

Slide the cable housing onto the new cable.

Re-insert the housing back into its holders.

Step 7

Slide the rear cable housing onto the new brake cable.
Re-insert the housing into its holders.

Slide the rear cable housing onto the new brake cable.

Re-insert the housing into its holders.

Step 8

Slide the screw and washer onto the end of the brake cable.
Slide the connector of over the screw and tighten the nut and washer on the other end by hand, so it can slide along the brake cable.

Slide the screw and washer onto the end of the brake cable.

Slide the connector of over the screw and tighten the nut and washer on the other end by hand, so it can slide along the brake cable.

Step 9

Flip bike back right-side-up.
Slide the connector up near the housing holder. About an inch between the connector and holder should be fine.
Using the smart wrench and 10mm socket wrench, tighten the nut so it grips the brake line firmly.
Using wire-cutters, cut the extra cable so only about an inch remains.

Flip bike back right-side-up.

Slide the connector up near the housing holder. About an inch between the connector and holder should be fine.

Using the smart wrench and 10mm socket wrench, tighten the nut so it grips the brake line firmly.

Using wire-cutters, cut the extra cable so only about an inch remains.

Step 10

You can recycle the old brake cable for this.
Insert the end of the brake cable with a “nub” into the slot on the rear left brake.
Slide the cable onto the slot on the connector.
Slide the other end of the cable into the holder on the right rear brake.
Pull the cable to clamp down the brakes so they almost touch the rim of the wheel.
Tighten the screw so the cable does not come loose.

You can recycle the old brake cable for this.

Insert the end of the brake cable with a “nub” into the slot on the rear left brake.

Slide the cable onto the slot on the connector.

Slide the other end of the cable into the holder on the right rear brake.

Pull the cable to clamp down the brakes so they almost touch the rim of the wheel.

Tighten the screw so the cable does not come loose.

You now should have a fully function rear brake on your bike.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Jacob Valdez

Member since: 02/24/2015

276 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team 23-4, Green Winter 2015                        

                                                  Member of Cal Poly, Team 23-4, Green Winter 2015 



                    CPSU-GREEN-W15S23G4                     


                                            7 Members                     


                                            13 Guides authored

DiY AnY - Jun 10, 2020

Добар текст са доста слика ево и текст са истом тему https://www.diyany.net/bicycle-cable-rep…

Introduction#

What you need#

Team#

Introduction

What you need

Team