Difficulty
Easy
Steps
7
Time Required
10 minutes
Sections
1
- How to Repair a Qianlong Rolling Office Chair
- 7 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackQianlong Rolling Office Chair
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
How to Repair a Qianlong Rolling Office Chair
- Carefully turn the chair over onto its side so that you have clear access to the underside of the seat.
- Remove the old bolts and hardware by unscrewing each bolt with your torque wrench, turning counterclockwise. We will be replacing them with new ones.
- We will be replacing them with new ones.
Carefully turn the chair over onto its side so that you have clear access to the underside of the seat.
Remove the old bolts and hardware by unscrewing each bolt with your torque wrench, turning counterclockwise. We will be replacing them with new ones.
We will be replacing them with new ones.
1024
Step 2
- Dust off both the underside of the seat and the metal plate with a paper towel to ensure they are both clean before reassembling.
Dust off both the underside of the seat and the metal plate with a paper towel to ensure they are both clean before reassembling.
Step 3
- Line up the holes of the metal plate with the holes under the seat, so that each bolt can be inserted without any trouble.
Line up the holes of the metal plate with the holes under the seat, so that each bolt can be inserted without any trouble.
Step 4
- Place a flat washer in front of one of the holes and make sure it lines up.
- Carefully insert one of the bolts through the washer and into the hole. Use your index and thumb to tighten the bolt as much as possible, by turning it clockwise. Doing so makes it easier to tighten with your wrench later.
- Please ensure you are using the correct size bolts. The bolts used in this guide are flat bolts 1/2" in length and 3/16" in diameter.
Place a flat washer in front of one of the holes and make sure it lines up.
Carefully insert one of the bolts through the washer and into the hole. Use your index and thumb to tighten the bolt as much as possible, by turning it clockwise. Doing so makes it easier to tighten with your wrench later.
Please ensure you are using the correct size bolts. The bolts used in this guide are flat bolts 1/2" in length and 3/16" in diameter.
Step 5
- Use your torque wrench to tighten the bolt the rest of the way by turning it clockwise, until it is very snug.
- Potential for device damage: Do not over-tighten, as doing so can damage the screw or the hole, which could leave it unusable.
- Repeat steps 3-5 with the remaining three holes.
Use your torque wrench to tighten the bolt the rest of the way by turning it clockwise, until it is very snug.
Potential for device damage: Do not over-tighten, as doing so can damage the screw or the hole, which could leave it unusable.
Repeat steps 3-5 with the remaining three holes.
Step 6
- Make any other adjustments as necessary. Use the big wheel located on the underside of the seat to tighten or loosen the back rest.
Make any other adjustments as necessary. Use the big wheel located on the underside of the seat to tighten or loosen the back rest.
Step 7
- Your Qianlong Rolling Office Chair is now repaired and ready for use!
Your Qianlong Rolling Office Chair is now repaired and ready for use!
Cancel: I did not complete this guide.
Author
with 3 other contributors
Cameron Todd
Member since: 10/09/2019
145 Reputation
1 Guide authored
Badges:
2
Team
Eastern Washington University, Team S27-G18, Munoz Fall 2019
Member of Eastern Washington University, Team S27-G18, Munoz Fall 2019
EWU-MUNOZ-F19S27G18
1 Member
1 Guide authored
