How To Open The Apple Tv 4K 2021 Siri Remote Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes - 1 hour

Sections

How to Open the Apple TV 4K 2021 Siri Remote
19 steps

Flags

BackApple TV 4K (2021)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Remove the bottom cover

Use a P2 Pentalope screwdriver to remove the two 6.1 mm-long screws securing the bottom cover.
Remove the bottom aluminium cover.

Use a P2 Pentalope screwdriver to remove the two 6.1 mm-long screws securing the bottom cover.

Remove the bottom aluminium cover.

1024

Step 2

              Create a gap

Insert an iFlex into the gap on the right side of the circular clickpad.
Insert the iFlex about 3 mm.
Use the iFlex to create a gap by prying the circular clickpad upwards.

Insert an iFlex into the gap on the right side of the circular clickpad.

Insert the iFlex about 3 mm.

Use the iFlex to create a gap by prying the circular clickpad upwards.

Step 3

              Unhinge the plastic clips

Insert an opening pick into the gap. Remove the iFlex after inserting the opening pick.
Slide the opening pick around the top half of the clickpad.
Avoid sliding the opening pick to the bottom half of the clickpad. A flex cable runs there!

Insert an opening pick into the gap. Remove the iFlex after inserting the opening pick.

Slide the opening pick around the top half of the clickpad.

Avoid sliding the opening pick to the bottom half of the clickpad. A flex cable runs there!

Step 4

              Remove the clickpad

Lift the clickpad from the lower right side to access the press connector.
Use an opening pick to pry up the clickpad connector to disconnect it.
Remove the clickpad.

Lift the clickpad from the lower right side to access the press connector.

Use an opening pick to pry up the clickpad connector to disconnect it.

Remove the clickpad.

Step 5

              Remove the face buttons

Insert the iFlex into the gap on the right edge of the volume button.
Insert the iFlex about 3 mm.

Insert the iFlex into the gap on the right edge of the volume button.

Insert the iFlex about 3 mm.

Step 6

              Unhinge the volume button

Use the iFlex to pry up the volume button to unhinge the plastic clips which keep the button in place.
Remove the volume button.

Use the iFlex to pry up the volume button to unhinge the plastic clips which keep the button in place.

Remove the volume button.

Step 7

Insert an angled probe into the housing to release the right plastic clip of the mute button.
Carefully push against the buttons clip from the inside.
Make sure that the probe doesn’t hit any components on the mainboard and is inserted horizontally.

Insert an angled probe into the housing to release the right plastic clip of the mute button.

Carefully push against the buttons clip from the inside.

Make sure that the probe doesn’t hit any components on the mainboard and is inserted horizontally.

Step 8

Insert the probe into the gap on the surface of the mute button.
Use the probe to pry up the mute button and unhinge the remaining plastic clips.
Remove the mute button

Insert the probe into the gap on the surface of the mute button.

Use the probe to pry up the mute button and unhinge the remaining plastic clips.

Remove the mute button

Step 9

Insert a probe into the case to release the right plastic clip of the play/pause button.
Gently press against the clip from the inside.
Make sure that the probe doesn’t hit any components on the mainboard and is inserted horizontally.

Insert a probe into the case to release the right plastic clip of the play/pause button.

Gently press against the clip from the inside.

Step 10

Insert the probe into the gap on the surface of the play/pause button.
Use the probe to pry up the play/pause button and unhinge the remaining plastic clips.
Remove the play/pause button.

Insert the probe into the gap on the surface of the play/pause button.

Use the probe to pry up the play/pause button and unhinge the remaining plastic clips.

Remove the play/pause button.

Step 11

Insert the probe into the housing where the clickpad was previously to release the upper plastic clip of the back button.
Carefully press against the clip from the inside.
Make sure that the probe doesn’t hit any components on the mainboard and is inserted horizontally.

Insert the probe into the housing where the clickpad was previously to release the upper plastic clip of the back button.

Carefully press against the clip from the inside.

Step 12

Insert the probe into the gap on the surface of the back button.
Use the probe to pry up the back button and unhinge the remaining plastic clips.
Remove the back button.

Insert the probe into the gap on the surface of the back button.

Use the probe to pry up the back button and unhinge the remaining plastic clips.

Remove the back button.

Step 13

Insert the probe into the inner housing where the clickpad used to be to release the upper plastic clip of the TV button.
Carefully press against the clip from the inside.
Make sure that the probe doesn’t hit any components on the mainboard and is inserted horizontally.

Insert the probe into the inner housing where the clickpad used to be to release the upper plastic clip of the TV button.

Step 14

Insert the probe into the gap on the surface of the TV button.
Use the probe to pry up the TV button and unhinge the remaining plastic clips.
Remove the TV button.

Insert the probe into the gap on the surface of the TV button.

Use the probe to pry up the TV button and unhinge the remaining plastic clips.

Remove the TV button.

Step 15

              Remove the Siri button

Use a T3 Torx screwdriver to remove the two 4.7 mm-long screws securing the Siri button on the right edge of the remote.

Use a T3 Torx screwdriver to remove the two 4.7 mm-long screws securing the Siri button on the right edge of the remote.

Step 16

Use the pointed end of a spudger or a pair of tweezers to lift the Siri button up and out of the remote.
Remove the Siri button.

Use the pointed end of a spudger or a pair of tweezers to lift the Siri button up and out of the remote.

Remove the Siri button.

Step 17

              Push the internal frame slightly out of the housing

Turn the remote upside down.
This will avoid the power button falling into the case and getting jammed.
Insert the flat end of a spudger into the charging port.
Don’t worry! This won’t damage the port.
Push the spudger in to slide the insides of the remote out about 1 inch (2.5 cm).
Don’t try to push it all out yet! The power button needs to be removed first.

Turn the remote upside down.

This will avoid the power button falling into the case and getting jammed.

Insert the flat end of a spudger into the charging port.

Don’t worry! This won’t damage the port.

Push the spudger in to slide the insides of the remote out about 1 inch (2.5 cm).

Don’t try to push it all out yet! The power button needs to be removed first.

Step 18

              Remove the power button

Turn the remote back over and make sure that the recess of the inner frame aligns with the power button.
Use the pointed end of a spudger to press the power button into the recess of the inner frame (if it didn’t already fall in by itself).
Remove the power button.

Turn the remote back over and make sure that the recess of the inner frame aligns with the power button.

Use the pointed end of a spudger to press the power button into the recess of the inner frame (if it didn’t already fall in by itself).

Remove the power button.

Step 19

              Remove the internal frame from the housing

Pull the inner frame out of its aluminum housing.
There is a slight resistance when pulling out.

Pull the inner frame out of its aluminum housing.

There is a slight resistance when pulling out.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for help.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Adriana Zwink

Member since: 12/18/2019

36,607 Reputation

                                      167 Guides authored                  



                       Badges:
                       34







                                                        +31 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Joanna - Jun 16, 2022

Hi,

Thank you so much for the guide - I was able to open up my coffee spilled on remote clean it and actually fix it! However…somewhere along the lines I broke the Siri button (it was working fine prior to me opening up the remote)! It’s a physical problem - I can’t push it down physically, there is no spring like behavior…was there something in between the button that I dislodged? Any ideas?

wolear - Aug 7, 2022

Whaa? I just wanted to slide out the module and desolder the Siri button in the same fashion I cleanly remove panic buttons on key fobs. I’ll be using JB Weld. Thank you for the heads up. Apple presenting two screws, lol!

Introduction#

What you need#

Team#

Introduction

What you need

Team