How To Fix Sticky Triggers Xbox One Wireless Controller Model 1708 Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 10 minutes

Sections

How To Fix Sticky Triggers Xbox One Wireless Controller Model 1708
4 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackXbox One Wireless Controller (Model 1708)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Get set up

Make sure you have all the pieces you need before beginning: Plastic or metal mini pry bars for removing the covers, small cotton buds for cleaning and rubbing alcohol for the actual cleaning part.
Have a clean desk or workspace with good lighting and make sure you are not hunched over while working (this is applicable to all work environments!)
Remove the batteries and the cover panel before doing any work on the controller.

Make sure you have all the pieces you need before beginning: Plastic or metal mini pry bars for removing the covers, small cotton buds for cleaning and rubbing alcohol for the actual cleaning part.

Have a clean desk or workspace with good lighting and make sure you are not hunched over while working (this is applicable to all work environments!)

Remove the batteries and the cover panel before doing any work on the controller.

1024

Step 2

              Removing the back panel

Using the pry bar, gently insert it near the base of the trigger to get under the plastic panel.
Then, with a lever action, slowly pry the panel off until you hear the plastic unsnapping from it’s mounting.
You might find it easier to swap between the front and back of the panel so as to not damage the panel if it is particularly sticky/stubborn.

Using the pry bar, gently insert it near the base of the trigger to get under the plastic panel.

Then, with a lever action, slowly pry the panel off until you hear the plastic unsnapping from it’s mounting.

You might find it easier to swap between the front and back of the panel so as to not damage the panel if it is particularly sticky/stubborn.

Step 3

              Cleaning the pads...

Clean the trigger contact pad with the cotton bud dipped in some rubbing alcohol. Be careful not to soak the cotton bud too much, you don’t want it dripping liquid inside the controller.
Also, clean the opposite surface on the underneath of the trigger key, the part that contacts the pad which is likely also sticky.
You can also see how much dust or dirt is inside the controller and in the cracks of the handles, might be a good time to tidy up!

Clean the trigger contact pad with the cotton bud dipped in some rubbing alcohol. Be careful not to soak the cotton bud too much, you don’t want it dripping liquid inside the controller.

Also, clean the opposite surface on the underneath of the trigger key, the part that contacts the pad which is likely also sticky.

You can also see how much dust or dirt is inside the controller and in the cracks of the handles, might be a good time to tidy up!

Step 4

              Finishing up...

Replace the plastic panel by dropping it into place then firmly pressing down on the top of the panel until you hear the clicking of the little clips inside.
Make sure it is properly reattached since there are a few clips inside which help to keep the panel in place, you don’t want this coming off again!
This can be done in the exact same way for both triggers, since they are both under an identical plastic panel and you can do this exact guide for both sides of the controller.

Replace the plastic panel by dropping it into place then firmly pressing down on the top of the panel until you hear the clicking of the little clips inside.

Make sure it is properly reattached since there are a few clips inside which help to keep the panel in place, you don’t want this coming off again!

This can be done in the exact same way for both triggers, since they are both under an identical plastic panel and you can do this exact guide for both sides of the controller.

To reassemble your device, follow these instructions in reverse order: simply snap the back panel(s) back into place, making sure they are firmly secured. Then reseat the batteries and cover (or your equivalent) and enjoy happy sticky-free gaming.

Cancel: I did not complete this guide.

                                                                                      18 other people completed this guide.

Author

                                      with 2 other contributors

                    Zach Smith

Member since: 09/06/2021

781 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Max Morin - Nov 23, 2021

The little rubber pad on mine is all torn up and is sticking really bad - ruining my Forza experience. I am going to scrape it all away, and replace it with a lil’ wee bit of felt. My guess is that all this little pad does is prevent the triggers from clicking too hard when bottoming out.

Zach Smith - Dec 12, 2021

Yes that should work, from my experience with fixing a few of these different types of console controllers. The rubber pad is just a cushion for the triggers to stop them hitting the frame of the controller so anything shock absorbing material should do it, just nothing that will stick to the triggers! :)

Moises rico - Aug 6, 2022

Ok, I had a problem with this and I thought this was it, but with some research later my situation spiraled into a monster of a problem with my trigger that require and entire replacement and I can’t find anything to help, not even a replacement part. If you can help, please do so

Zach Smith - Aug 10, 2022

Hello, thanks for reply seems like a weird issue, did you have a problem with the trigger sticking or that you can press it down but it doesn’t bounce back (like an issue with the trigger spring)?? I know that there is a small rubbery pad (see step 3 picture) that can come off and get stuck inside the trigger housing. Let me know some details and I will try to help :)

Daim Ur Rehman - Dec 28, 2022

Great guide helped fixing the issue.

Member-Contributed Guide#

Introduction#

What you need#

#

#

#

#

#

#

Member-Contributed Guide

Introduction

What you need