Difficulty
Moderate
Steps
16
Time Required
10 - 30 minutes
Sections
1
- How to Alter a Lengha Blouse
- 16 steps
Flags
0
BackClothing
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
This guide shows you step by step how to take in the blouse of a Lengha or any other traditional Indian outfits that come with similar blouses.
Special skills: A running stitch is required to take in the blouse, but this guide teaches you how to preform that task.
Warning: make sure to handle the needle with care, as it can easily be lost resulting in someone getting injured. It is suggested that you wear a guard on your fingers so you can protect yourself from being poked by the needle.
What you need
Step 1
How to Alter a Lengha Blouse
- Take the measuring tape and wrap it around under your bust. Take note of this measurement.
- Divide the measurement by two and take note. This will be the measurement used to tighten the blouse in step 4.
Take the measuring tape and wrap it around under your bust. Take note of this measurement.
Divide the measurement by two and take note. This will be the measurement used to tighten the blouse in step 4.
1024
Step 2
- Take the blouse, and flip it inside out.
- The inside of blouse must be facing outward.
Take the blouse, and flip it inside out.
The inside of blouse must be facing outward.
Step 3
- Lay the blouse with the front facing upward on a flat surface.
Lay the blouse with the front facing upward on a flat surface.
Step 4
- Stretch the measuring tape across the bottom of the blouse and use the measurement from step one to evenly measure how much to take it in on both sides.
Stretch the measuring tape across the bottom of the blouse and use the measurement from step one to evenly measure how much to take it in on both sides.
Step 5
- Use fabric chalk to mark where you will be sewing on each side of the blouse.
Use fabric chalk to mark where you will be sewing on each side of the blouse.
Step 6
- Select a thread that matches the blouse preferably, otherwise any color is fine.
- For clarity we will be using a yellow thread.
Select a thread that matches the blouse preferably, otherwise any color is fine.
For clarity we will be using a yellow thread.
Step 7
- Take the thread and insert it into the needles hole and pull approximately 30cm of the thread through.
- It is fine if there is extra thread remaining after the stitching.
Take the thread and insert it into the needles hole and pull approximately 30cm of the thread through.
It is fine if there is extra thread remaining after the stitching.
Step 8
- Put the two sides of the thread together to make a single thicker thread.
- Tie the end and cut the remaining thread, leaving you with a long line of thread for stitching.
Put the two sides of the thread together to make a single thicker thread.
Tie the end and cut the remaining thread, leaving you with a long line of thread for stitching.
Step 9
- Position the needle pointing upward at the bottom of the blouse, where it is marked with chalk to begin stitching.
Position the needle pointing upward at the bottom of the blouse, where it is marked with chalk to begin stitching.
Step 10
- Push needle upward through both pieces of the cloth.
- Pull through the entire thread until the knotted end of the thread stops the thread from being pulled any further.
Push needle upward through both pieces of the cloth.
Pull through the entire thread until the knotted end of the thread stops the thread from being pulled any further.
Step 11
- Measure a short interval and push the needle down into the blouse again.
Measure a short interval and push the needle down into the blouse again.
Step 12
- Continue steps 9-11 until you reach the top of the cloth. This will create a running stitch.
Continue steps 9-11 until you reach the top of the cloth. This will create a running stitch.
Step 13
- Tie a knot at the end of the stitch.
- Make sure it is close to the blouse. This photo demonstrates tying a knot away from the blouse.
Tie a knot at the end of the stitch.
Make sure it is close to the blouse. This photo demonstrates tying a knot away from the blouse.
Step 14
- Cut the excess thread at the top and bottom of the garment.
Cut the excess thread at the top and bottom of the garment.
Step 15
- Repeat Steps 9-14 for the other side of the blouse.
- Normally one side of the blouse will have a zipper. In that case it is not necessary to stitch the entire way through. Rather only stitch the part of the blouse that is already closed up.
- In this image, the zipper only opens until the visible point, therefore stitch above that area.
Repeat Steps 9-14 for the other side of the blouse.
Normally one side of the blouse will have a zipper. In that case it is not necessary to stitch the entire way through. Rather only stitch the part of the blouse that is already closed up.
In this image, the zipper only opens until the visible point, therefore stitch above that area.
Step 16
- Flip the blouse right side out, and now you have a complete fitted Lengha blouse.
Flip the blouse right side out, and now you have a complete fitted Lengha blouse.
Try the top on and check the fitting. If it seems too tight or loose, then you may have taken the wrong measurements. You may need to cut the stitches and try again. The fitting should ideally not be skin tight but rather allow a bit of room to breath since it is commonly a non-stretch material. Once you are done, you have now altered the blouse to your size and it is ready to be worn.
Cancel: I did not complete this guide.
Author
with 1 other contributor
aarushic
Member since: 01/14/2022
253 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
York University, Team R-5, Melo-Thaiss Winter 2022
Member of York University, Team R-5, Melo-Thaiss Winter 2022
YORK-MELO-THAISS-W22SRG5
1 Member
1 Guide authored
