Hover 1 Eclipse Shell Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Shell
6 steps

Flags

BackHover-1 Eclipse
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Shell

Using a Phillips #1 Screwdriver, remove the four 11mm screws that surround the edge of the plug side bottom shell piece.
Using a Phillips #1 Screwdriver, remove the four 13mm screws that surround the edge of the plug side bottom shell piece.
Remove the plug side bottom shell piece.
Be cautious of the wires connecting the plug side shell piece to the body. Do not pull the piece off until these wires have been disconnected in the following step.
Using a Phillips #1 Screwdriver, remove the four 11mm screws that surround the edge of the remaining bottom shell piece.
Using a Phillips #1 Screwdriver, remove the four 13mm screws that surround the edge of the remaining side bottom shell piece.
Remove final bottom shell piece

Using a Phillips #1 Screwdriver, remove the four 11mm screws that surround the edge of the plug side bottom shell piece.

Using a Phillips #1 Screwdriver, remove the four 13mm screws that surround the edge of the plug side bottom shell piece.

Remove the plug side bottom shell piece.

Be cautious of the wires connecting the plug side shell piece to the body. Do not pull the piece off until these wires have been disconnected in the following step.

Using a Phillips #1 Screwdriver, remove the four 11mm screws that surround the edge of the remaining bottom shell piece.

Using a Phillips #1 Screwdriver, remove the four 13mm screws that surround the edge of the remaining side bottom shell piece.

Remove final bottom shell piece

1024

Step 2

On the bottom plug side shell pieces, there are two white and pink wires connecting the shell and the motherboard.
On the circuit board by the speaker, carefully squeeze and unplug the small white headers that connect the shell piece to the hoverboard body.
Follow the wires that connect the lights to the motherboard. Disconnect these wires from the motherboard by squeezing and pulling the small white headers.
Now you can fully remove the bottom plug side shell piece.

On the bottom plug side shell pieces, there are two white and pink wires connecting the shell and the motherboard.

On the circuit board by the speaker, carefully squeeze and unplug the small white headers that connect the shell piece to the hoverboard body.

Follow the wires that connect the lights to the motherboard. Disconnect these wires from the motherboard by squeezing and pulling the small white headers.

Now you can fully remove the bottom plug side shell piece.

Step 3

Unplug the yellow tipped plug attached to the red and black cord on the non-battery side.

Unplug the yellow tipped plug attached to the red and black cord on the non-battery side.

Step 4

Using a Phillips #1 Screwdriver, remove the twelve 11mm and 13mm screws that line the bottom inside of the battery side of the Hover-1 Eclipse.
The screw placement is mirrored on the other side
Repeat these steps for the left inside of the Hover-1 Eclipse.

Using a Phillips #1 Screwdriver, remove the twelve 11mm and 13mm screws that line the bottom inside of the battery side of the Hover-1 Eclipse.

The screw placement is mirrored on the other side

Repeat these steps for the left inside of the Hover-1 Eclipse.

Step 5

Push down the shell and LED light near the center of the board as shown.
In the newly exposed area, there will be an 11mm screw holding in the wire that connects to the LED light of the frame. Remove this screw.
Now separate the light from the shell and board.
Repeat this for the other 3 lights.

Push down the shell and LED light near the center of the board as shown.

In the newly exposed area, there will be an 11mm screw holding in the wire that connects to the LED light of the frame. Remove this screw.

Now separate the light from the shell and board.

Repeat this for the other 3 lights.

Step 6

Follow the rainbow cord that connects the left side shell piece to the inside board. Find where it is plugged into and disconnect it.
The cord is a bundle of multicolored wires sheathed in black, halfway down.
Follow the black and blue cord that connects the left side shell piece to the inside board. Find where it is plugged into and disconnect it.
Repeat for the top right shell piece.
Remove both shell pieces.

Follow the rainbow cord that connects the left side shell piece to the inside board. Find where it is plugged into and disconnect it.

The cord is a bundle of multicolored wires sheathed in black, halfway down.

Follow the black and blue cord that connects the left side shell piece to the inside board. Find where it is plugged into and disconnect it.

Repeat for the top right shell piece.

Remove both shell pieces.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Stone Burgan

Member since: 10/10/2019

133 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team S12-G4, Regan Fall 2019                        

                                                  Member of Cal Poly, Team S12-G4, Regan Fall 2019 



                    CPSU-REGAN-F19S12G4                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team