Difficulty

Moderate

Steps

14

Time Required

                          45 minutes

Sections

1

  • Outer Shell
  • 14 steps

Flags

0

  • BackHover-1 Charger

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

In this guide, the right or left cover refers to the portion of the outer shell that contains the LED headlights. The right or left foot pad refers to the portion of the outer shell that the user places their foot on.

Make sure to wear an anti-static wrist strap to protect the electronics against buildup of static electricity. Some screw housings are fragile; they may fall apart when the screw is removed.

What you need

Step 1

              Outer Shell
  • Flip the hoverboard over so that the warning label is facing up.
  • Remove the twelve 12 mm screws with a Phillips #2 screwdriver.
  • Remove the four 10 mm screws with a Phillips #2 screwdriver.
  • The screws nearest to the wheels may be hard to access. Be sure to use a long, thin screwdriver.

Flip the hoverboard over so that the warning label is facing up.

Remove the twelve 12 mm screws with a Phillips #2 screwdriver.

Remove the four 10 mm screws with a Phillips #2 screwdriver.

The screws nearest to the wheels may be hard to access. Be sure to use a long, thin screwdriver.

1024

Step 2

  • Pull the right cover away from the hoverboard.

Pull the right cover away from the hoverboard.

Step 3

  • Unscrew four 12 mm screws that hold the right foot pad with a Philips #2 screwdriver.
  • Unscrew the four 18 mm screws with a Philips #2 screwdriver.
  • Use a long, thin screwdriver to access the two 12 mm screws nearest to the wheel.

Unscrew four 12 mm screws that hold the right foot pad with a Philips #2 screwdriver.

Unscrew the four 18 mm screws with a Philips #2 screwdriver.

Use a long, thin screwdriver to access the two 12 mm screws nearest to the wheel.

Step 4

  • Unplug the battery by disconnecting the two pronged black and yellow cable.

Unplug the battery by disconnecting the two pronged black and yellow cable.

Step 5

  • Unplug the black, yellow, green and red four pin connector from the circuit board.
  • Unplug the red and black two pin connector from the circuit board.

Unplug the black, yellow, green and red four pin connector from the circuit board.

Unplug the red and black two pin connector from the circuit board.

Step 6

  • Thread the black, yellow, green, and red four pin connector through the opening to the left of the battery.
  • Remove the right foot pad from the hoverboard.

Thread the black, yellow, green, and red four pin connector through the opening to the left of the battery.

Remove the right foot pad from the hoverboard.

Step 7

  • Pull the left cover away from the hoverboard.

Pull the left cover away from the hoverboard.

Step 8

  • Unplug the red and white five pin connector from the circuit board.
  • Thread this connector through the middle cylinder.
  • Remove the right cover from the hoverboard.

Unplug the red and white five pin connector from the circuit board.

Thread this connector through the middle cylinder.

Remove the right cover from the hoverboard.

Step 9

  • Unplug the red and white four pin connector from the speaker circuit board.
  • Unplug the blue and white three pin connector.
  • Unplug the blue and white two pin connector. This is photographed as an example.

Unplug the red and white four pin connector from the speaker circuit board.

Unplug the blue and white three pin connector.

Unplug the blue and white two pin connector. This is photographed as an example.

Step 10

  • Remove the left cover from the hoverboard.

Remove the left cover from the hoverboard.

Step 11

  • Disconnect the two pronged black and yellow cable.

Disconnect the two pronged black and yellow cable.

Step 12

  • Remove three black and red two pin connectors from the left circuit board.
  • Remove the red, yellow, and black three pin connector.
  • Remove zip tie if present.

Remove three black and red two pin connectors from the left circuit board.

Remove the red, yellow, and black three pin connector.

Remove zip tie if present.

Step 13

  • Unscrew four 12 mm screws from the sides holding the left foot pad with a Phillips #2 screwdriver.
  • Unscrew four 18 mm screws with a Phillips #2 screwdriver.
  • Use a long, thin screwdriver to access the two 12 mm screws nearest to the wheel.

Unscrew four 12 mm screws from the sides holding the left foot pad with a Phillips #2 screwdriver.

Unscrew four 18 mm screws with a Phillips #2 screwdriver.

Step 14

  • Remove the left foot pad from the hoverboard.

Remove the left foot pad from the hoverboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Mark Rapiz

Member since: 10/10/2019

229 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team S12-G1, Regan Fall 2019                        

                                                  Member of Cal Poly, Team S12-G1, Regan Fall 2019 



                    CPSU-REGAN-F19S12G1                     


                                            4 Members                     


                                            6 Guides authored

firestineanthony - Mar 15, 2020

Reply

Where do I buy the shell their website doesnt have it