Difficulty
Easy
Steps
9
Time Required
10 - 15 minutes
Sections
2
- Plastic Assembly
- 4 steps
- Front Panel
- 5 steps
Flags
0
BackHoneywell HY 254 TGT
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Plastic Assembly
- Remove the two 3/4" wing screws on the bottom of the fan by rotating them counter-clockwise.
Remove the two 3/4" wing screws on the bottom of the fan by rotating them counter-clockwise.
1024
Step 2
- Twist the fan base counter-clockwise until the pins line up as shown.
- Pull the base straight towards you to remove it, feeding the wire through the base.
Twist the fan base counter-clockwise until the pins line up as shown.
Pull the base straight towards you to remove it, feeding the wire through the base.
Step 3
- Remove all of the marked 1/2" Phillips #02 screws on the backside of the fan
- Remove the two marked 3/4" Phillips #02 screws in the middle.
Remove all of the marked 1/2" Phillips #02 screws on the backside of the fan
Remove the two marked 3/4" Phillips #02 screws in the middle.
Step 4
- Use a plastic opening tool or screwdriver to pry off the back of the fan, starting from the top down.
- Be aware of two clips inside the fan, towards the bottom third of the fan. If the back appears stuck on certain spots, push inward edges of the front casing around the problematic area.
Use a plastic opening tool or screwdriver to pry off the back of the fan, starting from the top down.
Be aware of two clips inside the fan, towards the bottom third of the fan. If the back appears stuck on certain spots, push inward edges of the front casing around the problematic area.
Step 5
Front Panel
- Remove the four 1/2" Phillips #02 screws, indicated by a red circle.
- Lean the front panel forwards and set it down.
- The front panel will not fully detach and cannot be removed. Do not try to forcibly remove it, as it may cause damage to the electronics.
Remove the four 1/2" Phillips #02 screws, indicated by a red circle.
Lean the front panel forwards and set it down.
The front panel will not fully detach and cannot be removed. Do not try to forcibly remove it, as it may cause damage to the electronics.
Step 6
- Gently lift and remove the panel covering the electronics assembly.
Gently lift and remove the panel covering the electronics assembly.
Step 7
- Remove the four 1/2" Phillips #01 screws in the circuit board.
- Gently pull the circuit board off of the rest of the front panel assembly.
Remove the four 1/2" Phillips #01 screws in the circuit board.
Gently pull the circuit board off of the rest of the front panel assembly.
Step 8
- Lift out the internal part of the front panel to access the buttons.
Lift out the internal part of the front panel to access the buttons.
Step 9
- If necessary, remove the buttons by grabbing them with two fingers and pulling up and away from the panel.
- Upon reassembly, ensure buttons are placed in the correct location.
If necessary, remove the buttons by grabbing them with two fingers and pulling up and away from the panel.
Upon reassembly, ensure buttons are placed in the correct location.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
Darian Maxwell
Member since: 10/01/2015
366 Reputation
2 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 11-6, Forte Fall 2015
Member of Cal Poly, Team 11-6, Forte Fall 2015
CPSU-FORTE-F15S11G6
4 Members
4 Guides authored
