Holmes Blizzard Fan Oscillation Gear Replacement Repair Guide

Difficulty

Easy

Steps

12

Time Required

                          20 minutes            

Sections

2

• Oscillation Button
• 8 steps
• Oscillation Gear
• 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackHolmes Blizzard Fan

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Front Cage Removal               

• Using a Phillips #2 Screwdriver, remove the 3 screws located on the back of the fan cage.
• Next, loosen the screw located on the bottom of the fan.
• The bottom screw does not need to be removed, but only loosened about 3 or 4 turns.
• The front of the fan’s cage is now able to be removed by prying the front away from the back.

Using a Phillips #2 Screwdriver, remove the 3 screws located on the back of the fan cage.

Next, loosen the screw located on the bottom of the fan.

The bottom screw does not need to be removed, but only loosened about 3 or 4 turns.

The front of the fan’s cage is now able to be removed by prying the front away from the back.

1024

Step 2

• Using a 7 mm socket and wrench, remove the 2 nuts that are behind the fan blades.
• There is a washer located behind each nut. Be sure not to lose these.

Using a 7 mm socket and wrench, remove the 2 nuts that are behind the fan blades.

There is a washer located behind each nut. Be sure not to lose these.

Step 3

              Remove the Oscillation Button Screw               

• On the top of the fan, there is a screw fastening the oscillation button to the gear train within the housing. Remove this screw with the Phillips #0 Screwdriver.

On the top of the fan, there is a screw fastening the oscillation button to the gear train within the housing. Remove this screw with the Phillips #0 Screwdriver.

Step 4

              Housing Assembly Removal               

• The on/off and fan speed nob can be removed by simply pulling it away from the main housing.

The on/off and fan speed nob can be removed by simply pulling it away from the main housing.

Step 5

• Remove the 2 screws holding the clear plastic plate in place with a Phillips #2 Screwdriver.
• The plate is now free and can be taken out by hand.

Remove the 2 screws holding the clear plastic plate in place with a Phillips #2 Screwdriver.

The plate is now free and can be taken out by hand.

Step 6

• The motor switch is also free and can be removed by hand to reveal a screw holding the housing assembly in place.
• Be sure not to damage the wires on the switch during removal. While you do not need to be overly gentle during this step, excessive force could cause the wires to be pulled out.

The motor switch is also free and can be removed by hand to reveal a screw holding the housing assembly in place.

Be sure not to damage the wires on the switch during removal. While you do not need to be overly gentle during this step, excessive force could cause the wires to be pulled out.

Step 7

• Remove the screw that holds the housing assembly in place by using a Phillips #2 Screwdriver.

Remove the screw that holds the housing assembly in place by using a Phillips #2 Screwdriver.

Step 8

• The housing assembly can now be pulled off and pushed to the side to reveal the fan motor and gear train.
• The oscillation button the was unscrewed earlier will fall out of the housing assembly.

The housing assembly can now be pulled off and pushed to the side to reveal the fan motor and gear train.

The oscillation button the was unscrewed earlier will fall out of the housing assembly.

Step 9

              Oscillation Gear Removal               

• Remove the 2 screws fastening the lid on the oscillation gear housing with a Flathead Screwdriver.

Remove the 2 screws fastening the lid on the oscillation gear housing with a Flathead Screwdriver.

Step 10

• Using your thumb, the lid can easily be popped off to reveal the oscillation gear.

Using your thumb, the lid can easily be popped off to reveal the oscillation gear.

Step 11

• The oscillation gear is removed by pressing it up from the bottom.

The oscillation gear is removed by pressing it up from the bottom.

Step 12

• The oscillation gear has been removed and fresh grease can be applied or it can be replaced.

The oscillation gear has been removed and fresh grease can be applied or it can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Mike Bolton                     

Member since: 07/17/2016

474 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Keith Beba - May 25, 2020

Reply

Do you know where the oscillation gear can be purchased?