Difficulty

Difficult

Steps

22

Time Required

                          45 minutes - 1 hour

Sections

7

  • Rear Case
  • 2 steps
  • Screen
  • 3 steps
  • Digitizer
  • 3 steps
  • Camera
  • 2 steps
  • Wifi Antenna
  • 3 steps
  • Battery
  • 4 steps
  • Motherboard
  • 5 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHKC P776A

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Separating Digitizer and Case
  • Insert the plastic opening tool between the digitizer and the case.
  • Place the spudger in the gap created by the plastic opening tool to assist in separation.

Insert the plastic opening tool between the digitizer and the case.

Place the spudger in the gap created by the plastic opening tool to assist in separation.

1024

Step 2

  • Slide the spudger along the perimeter of the device to fully separate the two pieces.

Slide the spudger along the perimeter of the device to fully separate the two pieces.

Step 3

              Separating the Screen and Digitizer
  • Use your fingers to pop the screen out from the digitizer.

Use your fingers to pop the screen out from the digitizer.

Step 4

              Removing the Optical Cord from the Motherbaord
  • With the plastic opening tool, lift the black latch up.

With the plastic opening tool, lift the black latch up.

Step 5

  • Pull the optical cord out from the motherboard.

Pull the optical cord out from the motherboard.

Step 6

              Separating the Screen and the Digitizer

Step 7

              Removing the Cable from the Motherboard
  • Use the tip of the spudger to release the latches on the motherboard.

Use the tip of the spudger to release the latches on the motherboard.

Step 8

  • Remove the cable from the motherboard.

Remove the cable from the motherboard.

Step 9

              Removing the Cable from the Moatherboard

Step 10

  • Remove the camera from the device.

Remove the camera from the device.

Step 11

              Wifi Antenna
  • Peel off the tape that is attaching the wifi antenna to the case.

Peel off the tape that is attaching the wifi antenna to the case.

Step 12

  • Using the soldering iron, heat up the solder that is attaching the antenna to the motheboard.
  • The heat from the soldering iron may cause personal injury or damage the internal components of the tablet.

Using the soldering iron, heat up the solder that is attaching the antenna to the motheboard.

The heat from the soldering iron may cause personal injury or damage the internal components of the tablet.

Step 13

  • Suck up the leftover solder using the desoldering pump.
  • Remove the wifi antenna from the motherboard.

Suck up the leftover solder using the desoldering pump.

Remove the wifi antenna from the motherboard.

Step 14

              Battery
  • Insert the plastic opening tool between the battery and case.
  • Apply leverage to break the glue that is attaching the battery to the case.

Insert the plastic opening tool between the battery and case.

Apply leverage to break the glue that is attaching the battery to the case.

Step 15

  • Continue breaking the glue along the perimeter of the battery until the battery can be removed.
  • Breaking all the glue between the battery and case may take a long time.

Continue breaking the glue along the perimeter of the battery until the battery can be removed.

Breaking all the glue between the battery and case may take a long time.

Step 16

  • Using the soldering iron, heat up the solder that is attaching the battery to the motheboard.
  • The heat from the soldering iron may cause personal injury or damage the internal components of the tablet.

Using the soldering iron, heat up the solder that is attaching the battery to the motheboard.

Step 17

  • Suck up the leftover solder using the desoldering pump.
  • Remove the battery from the motherboard.

Remove the battery from the motherboard.

Step 18

              Motherboard
  • Using the screwdriver, remove the four 4mm by 1.5mm screws that are attaching the motherboard to the case.

Using the screwdriver, remove the four 4mm by 1.5mm screws that are attaching the motherboard to the case.

Step 19

  • Remove the black material that is covering the speaker.

Remove the black material that is covering the speaker.

Step 20

  • Insert the spudger into the speaker slot on the back of the case.

Insert the spudger into the speaker slot on the back of the case.

Step 21

  • Push the speaker out of the case with the spudger.

Push the speaker out of the case with the spudger.

Step 22

  • Remove the motherboard from the case.

Remove the motherboard from the case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Ryan Gornati

Member since: 01/22/2015

409 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team 7-6, Remmell Winter 2015                        

                                                  Member of USF Tampa, Team 7-6, Remmell Winter 2015 



                    USFT-REMMELL-W15S7G6                     


                                            3 Members                     


                                            14 Guides authored