Difficulty
Moderate
Steps
9
Time Required
15 - 20 minutes
Sections
2
- Rear Case
- 6 steps
- Battery
- 3 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackHipstreet Titan 2 HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Case
- Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.
- The screws are located on the bottom face of the device, near the power and volume controls.
Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.
The screws are located on the bottom face of the device, near the power and volume controls.
1024
Step 2
- Place the small suction cup on your screen.
- Moisturize the bottom of the suction cup to ensure a proper seal.
- If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.
Place the small suction cup on your screen.
Moisturize the bottom of the suction cup to ensure a proper seal.
If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.
Step 3
- Insert the plastic opening tool between the screen cover and rear cover of the tablet.
- Grasp the small suction cup.
Insert the plastic opening tool between the screen cover and rear cover of the tablet.
Grasp the small suction cup.
Step 4
- Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.
- Pull upward on the small suction cup handle while sliding the opening tool.
- When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.
Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.
Pull upward on the small suction cup handle while sliding the opening tool.
When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.
Step 5
- Use the plastic opening tool to remove the speaker from the rear cover.
- The speaker is held in place with adhesive and is easily removed.
- Do not pull on the speaker wires. This could damage the soldering connections.
Use the plastic opening tool to remove the speaker from the rear cover.
The speaker is held in place with adhesive and is easily removed.
Do not pull on the speaker wires. This could damage the soldering connections.
Step 6
- Once the speaker is disconnected, the cover removal is complete.
Once the speaker is disconnected, the cover removal is complete.
Step 7
Battery
- Remove the black placement tape from the battery.
- Find the two battery solder connections on the circuit board.
Remove the black placement tape from the battery.
Find the two battery solder connections on the circuit board.
Step 8
- Remove the red and black battery wires from the circuit board with the solder removal tool.
Remove the red and black battery wires from the circuit board with the solder removal tool.
Step 9
- Solder the new battery wire connectors to the circuit board.
- The battery wires must be installed with the red wire on the left and black wire on the right.
Solder the new battery wire connectors to the circuit board.
The battery wires must be installed with the red wire on the left and black wire on the right.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Jeffrey
Member since: 03/11/2015
766 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Colorado Springs, Team 5-6, Panko Spring 2015
Member of Colorado Springs, Team 5-6, Panko Spring 2015
UCCS-PANKO-S15S5G6
3 Members
10 Guides authored
