Difficulty
Difficult
Steps
10
Time Required
20 minutes
Sections
3
- Battery
- 3 steps
- Touchpad Plane/Keyboard
- 4 steps
- Fan/Motherboard
- 3 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackHannspree SN12E2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Unplug and power off your laptop.
Unplug and power off your laptop.
1024
Step 2
- Close your laptop .
- Place your laptop face down on a flat surface.
Close your laptop .
Place your laptop face down on a flat surface.
Step 3
- Unlatch the lock on the top right of your laptop first.
- You will need to pull on the lock on the left side and remove the battery at the same time
- The left lock is a spring lock and needs constant pressure applied in order to stay open.
Unlatch the lock on the top right of your laptop first.
You will need to pull on the lock on the left side and remove the battery at the same time
The left lock is a spring lock and needs constant pressure applied in order to stay open.
Step 4
Touchpad Plane/Keyboard
- Remove all the 5mm PH0 screws on the back cover
Remove all the 5mm PH0 screws on the back cover
Step 5
- Gently pry the case apart starting at the lower right corner using the small spudger
- Move around the case gently prying until the touchpad plane is free from the rest of the case
Gently pry the case apart starting at the lower right corner using the small spudger
Move around the case gently prying until the touchpad plane is free from the rest of the case
Step 6
- Gently lift up on the touchpad portion of the touchpad plane
- Unplug the ZIFF connector by pulling gently on the black retaining blade and removing the white flat flex cable
- Pull the touchpad away from the rest of the case
Gently lift up on the touchpad portion of the touchpad plane
Unplug the ZIFF connector by pulling gently on the black retaining blade and removing the white flat flex cable
Pull the touchpad away from the rest of the case
Step 7
- Gently lift up on the loose keyboard to expose the ZIFF connector.
- Unplug the keyboard ZIFF following the same instructions as the touchpad ZIFF
Gently lift up on the loose keyboard to expose the ZIFF connector.
Unplug the keyboard ZIFF following the same instructions as the touchpad ZIFF
Step 8
Fan/Motherboard
- Remove 3.4mm PH0 retaining screws as well as the three 3mm PH0 fan screws
Remove 3.4mm PH0 retaining screws as well as the three 3mm PH0 fan screws
Step 9
- Unplug all pictured connectors
Unplug all pictured connectors
Step 10
- Remove the motherboard from the housing place it on a flat surface.
- Flip over the motherboard so that the heat pipes ae face up.and disconnect fan JST Connector, pictured in red
Remove the motherboard from the housing place it on a flat surface.
Flip over the motherboard so that the heat pipes ae face up.and disconnect fan JST Connector, pictured in red
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Brianna Johnson
Member since: 03/21/2019
413 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team S2-G2, Simcock Spring 2019
Member of UMass Dartmouth, Team S2-G2, Simcock Spring 2019
UMASSD-SIMCOCK-S19S2G2
4 Members
9 Guides authored
