Difficulty

Moderate

Steps

13

Time Required

                          15 minutes

Sections

3

  • Back Panel
  • 5 steps
  • Battery
  • 4 steps
  • Wi-Fi Card Replacement
  • 4 steps

Flags

0

  • BackHannspree Hannspad SN1AT71

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Place the tablet screen side up.
  • Make sure the device is turned off to avoid damage.

Place the tablet screen side up.

Make sure the device is turned off to avoid damage.

1024

Step 2

  • Use the metal spudger to press an opening between the screen and back cover.
  • The plastic tabs are located on each corner of the back cover.
  • Be careful, as the plastic tabs are delicate.

Use the metal spudger to press an opening between the screen and back cover.

The plastic tabs are located on each corner of the back cover.

Be careful, as the plastic tabs are delicate.

Step 3

  • Wedge the plastic opening tool between the screen and the back panel to prevent re-engagement

Wedge the plastic opening tool between the screen and the back panel to prevent re-engagement

Step 4

  • Slide the metal spudger around the casing to separate it from the inside of the tablet.

Slide the metal spudger around the casing to separate it from the inside of the tablet.

Step 5

  • Flip the tablet over so the screen side is down after all the tabs are separated.
  • Remove the back panel by delicately lifting it straight up.

Flip the tablet over so the screen side is down after all the tabs are separated.

Remove the back panel by delicately lifting it straight up.

Step 6

              Battery
  • Remove the adhesive tape from the power connection cables.

Remove the adhesive tape from the power connection cables.

Step 7

  • Instructions for desoldering can be found on the iFixit website.
  • The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.
  • Grab hold of the red wire using the tweezers.
  • Desolder the red wire connection from the motherboard using the tip of the soldering iron.
  • Move the wire connection away from the motherboard.
  • Do not let the red wire connection touch other wires or the motherboard.

Instructions for desoldering can be found on the iFixit website.

The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.

Grab hold of the red wire using the tweezers.

Desolder the red wire connection from the motherboard using the tip of the soldering iron.

Move the wire connection away from the motherboard.

Do not let the red wire connection touch other wires or the motherboard.

Step 8

  • Desolder the black and yellow wire connection from the motherboard by following the previous step.
  • When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

Desolder the black and yellow wire connection from the motherboard by following the previous step.

When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

Step 9

  • Insert the flat end of the nylon spudger between the battery and the case.
  • The battery is connected to the tablet with an adhesive tape and will come free slowly.
  • Do not puncture or bend the battery while removing. If your battery is swollen, take appropriate precautions.

Insert the flat end of the nylon spudger between the battery and the case.

The battery is connected to the tablet with an adhesive tape and will come free slowly.

Do not puncture or bend the battery while removing. If your battery is swollen, take appropriate precautions.

Step 10

              Wi-Fi Card Replacement
  • Identify the card and its connection to the motherboard.
  • The card itself.
  • The area where the card connects to the motherboard.

Identify the card and its connection to the motherboard.

The card itself.

The area where the card connects to the motherboard.

Step 11

  • Peel off the adhesive tape holding the wires down.

Peel off the adhesive tape holding the wires down.

Step 12

  • Desolder the wire.

Desolder the wire.

Step 13

  • Use the tweezers to peel the Wi-Fi card off.

Use the tweezers to peel the Wi-Fi card off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors 


                    matthew vandeventer

Member since: 03/11/2015

908 Reputation

                                      5 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges

Team

                       Colorado Springs, Team 9-4, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 9-4, Panko Spring 2015 



                    UCCS-PANKO-S15S9G4                     


                                            3 Members                     


                                            10 Guides authored