Gopro Hero 3 Silver Motherboard Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

Suggest a time??

Sections

Battery
2 steps
Motherboard
8 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackGoPro HERO3 Silver
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Battery

Pull back on the tab on the back of GoPro to open the battery cover.

Pull back on the tab on the back of GoPro to open the battery cover.

1024

Step 2

Pull the battery out using the tab.

Pull the battery out using the tab.

Step 3

              Motherboard

Use the plastic opening tool to remove the faceplate.
There is some adhesive and clips so be careful and the faceplate should pop right off.

Use the plastic opening tool to remove the faceplate.

There is some adhesive and clips so be careful and the faceplate should pop right off.

Step 4

Now that the faceplate is off, it is time to remove the 4 screws on each corner.
Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

Now that the faceplate is off, it is time to remove the 4 screws on each corner.

Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

Step 5

Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.
Using the plastic opening tool, slowly pry open the motherboard assembly.

Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

Using the plastic opening tool, slowly pry open the motherboard assembly.

Step 6

Use the spudger to gently pry off the connector of the housing to the motherboard.
You should now have the motherboard assembly and the housing separated.

Use the spudger to gently pry off the connector of the housing to the motherboard.

You should now have the motherboard assembly and the housing separated.

Step 7

Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.
Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.
Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

Step 8

The media adapter is attached to the motherboard via 3 screws:
x1 T4 Torx
x2 Phillips #00
There’s a little silver bracket that is held down by the Phillips #00 screw so be careful not to lose it.
With a little prying, use the spudger to detach the media adapter’s connector from the motherboard.

The media adapter is attached to the motherboard via 3 screws:

x1 T4 Torx

x2 Phillips #00

There’s a little silver bracket that is held down by the Phillips #00 screw so be careful not to lose it.

With a little prying, use the spudger to detach the media adapter’s connector from the motherboard.

Step 9

Use the spudger to lift the black tab up to unlock.
Then remove LCD screen connector by sliding out.

Use the spudger to lift the black tab up to unlock.

Then remove LCD screen connector by sliding out.

Step 10

Using the Phillips head bit, remove the silver screw near the top edge of the board.
Separate the LCD assembly by pulling it away. You should have the bare motherboard!

Using the Phillips head bit, remove the silver screw near the top edge of the board.

Separate the LCD assembly by pulling it away. You should have the bare motherboard!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      15 other people completed this guide.

Author

                                      with 4 other contributors

                    Brian Alvarez

Member since: 04/02/2015

1,415 Reputation

                                      6 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 24-7, Lancaster Spring 2015                        

                                                  Member of Cal Poly, Team 24-7, Lancaster Spring 2015 



                    CPSU-LANCASTER-S15S24G7                     


                                            3 Members                     


                                            21 Guides authored

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team