Google Pixel 4A 5G Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

SIM Card Tray
1 step
Screen
15 steps
Battery Disconnect
7 steps
Back Cover
3 steps
Loudspeaker
4 steps
Front-Facing Camera
2 steps
Motherboard Removal
7 steps
Rear-Facing Camera
3 steps
Motherboard
1 step

Flags

BackGoogle Pixel 4a 5G
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Follow this guide to replace the motherboard on a Google Pixel 4a 5G.

The unreinforced display panel on the Pixel 4a 5G is fragile. Pay special attention to the warnings in the opening procedure if you are reusing the screen.

What you need

Step 1

              Eject the SIM card tray

Insert a SIM eject tool, bit, or straightened paper clip into the SIM tray hole.
Press directly into the hole to eject the SIM card tray.
Remove the SIM card tray.

Insert a SIM eject tool, bit, or straightened paper clip into the SIM tray hole.

Press directly into the hole to eject the SIM card tray.

Remove the SIM card tray.

1024

Step 2

              Precautionary Notes

You will need to pry the screen up to remove it from the phone. Read the following notes carefully before proceeding.
Take note of the two seams on the edge of your phone:
Screen seam: This seam separates the screen from the rest of the phone. This is where you have to pry.
Frame seam: This is where the plastic frame meets the back cover. It is held in place by screws. Do not pry at this seam.
Before you begin, note the following areas on the screen:
Screen flex cable: Do not insert the opening pick deeper than instructed or you risk damaging this cable.
Adhesive perimeter: Prying beyond this narrow perimeter without angling the pick will damage the OLED panel.

You will need to pry the screen up to remove it from the phone. Read the following notes carefully before proceeding.

Take note of the two seams on the edge of your phone:

Screen seam: This seam separates the screen from the rest of the phone. This is where you have to pry.

Frame seam: This is where the plastic frame meets the back cover. It is held in place by screws. Do not pry at this seam.

Before you begin, note the following areas on the screen:

Screen flex cable: Do not insert the opening pick deeper than instructed or you risk damaging this cable.

Adhesive perimeter: Prying beyond this narrow perimeter without angling the pick will damage the OLED panel.

Step 3

              Heat the right edge of the screen

Apply a heated iOpener to the right edge of the display for one minute to soften the adhesive.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Apply a heated iOpener to the right edge of the display for one minute to soften the adhesive.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Step 4

              Insert an opening pick

If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.
Place a suction cup as close to the right edge of the screen as possible.
Lift the suction cup with a strong steady force.
Insert the tip of an opening pick into the screen seam no more than 1 mm.

If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Place a suction cup as close to the right edge of the screen as possible.

Lift the suction cup with a strong steady force.

Insert the tip of an opening pick into the screen seam no more than 1 mm.

Step 5

              Guide the opening pick under the OLED panel

This step shows how to insert your pick without damaging the OLED panel. Do this before slicing the adhesive.
With the pick 1 mm into the gap, pivot the pick upwards to a steep angle.
At a steep angle, carefully push the pick into the gap about 1/4 inch (6 mm). The pick should slide in below the OLED panel.
Stop if you feel the point of the pick hitting a ridge. The pick may be pressing against the edge of the OLED panel. Angle the pick and try again.

This step shows how to insert your pick without damaging the OLED panel. Do this before slicing the adhesive.

With the pick 1 mm into the gap, pivot the pick upwards to a steep angle.

At a steep angle, carefully push the pick into the gap about 1/4 inch (6 mm). The pick should slide in below the OLED panel.

Stop if you feel the point of the pick hitting a ridge. The pick may be pressing against the edge of the OLED panel. Angle the pick and try again.

Step 6

              Slice through the display adhesive

Slide the pick along the right edge of the screen to cut the adhesive.
Do not insert the pick more than 1/4 inch (6 mm) or you may damage the screen’s flex cable.
Leave the pick in the bottom-right corner to prevent the adhesive from re-sealing.

Slide the pick along the right edge of the screen to cut the adhesive.

Do not insert the pick more than 1/4 inch (6 mm) or you may damage the screen’s flex cable.

Leave the pick in the bottom-right corner to prevent the adhesive from re-sealing.

Step 7

There’s a mesh covering the earpiece speaker on the top edge of the screen. If you don’t have a replacement mesh, take care not to damage or lose this component.
The screen adhesive is weak, so you should not need to re-apply heat. If the screen is hard to slice, apply heat to the difficult area for one minute and try again.
Insert another opening pick into the right edge of the phone at an angle where a gap has already formed to prevent damage to the OLED panel.
Slide the opening pick around the top of the phone to cut the adhesive.
Leave the pick inserted along the top edge to prevent the adhesive from resealing.

There’s a mesh covering the earpiece speaker on the top edge of the screen. If you don’t have a replacement mesh, take care not to damage or lose this component.

The screen adhesive is weak, so you should not need to re-apply heat. If the screen is hard to slice, apply heat to the difficult area for one minute and try again.

Insert another opening pick into the right edge of the phone at an angle where a gap has already formed to prevent damage to the OLED panel.

Slide the opening pick around the top of the phone to cut the adhesive.

Leave the pick inserted along the top edge to prevent the adhesive from resealing.

Step 8

Insert another opening pick into the top edge of your phone at an angle where a gap has already formed to prevent damage to the OLED panel.
Use the pick to slice around the top-left corner where the camera window is.
If the screen is hard to slice, apply heat to the difficult area for one minute and try again.
Leave the pick inserted along the left edge of your phone to prevent the adhesive from re-sealing.

Insert another opening pick into the top edge of your phone at an angle where a gap has already formed to prevent damage to the OLED panel.

Use the pick to slice around the top-left corner where the camera window is.

If the screen is hard to slice, apply heat to the difficult area for one minute and try again.

Leave the pick inserted along the left edge of your phone to prevent the adhesive from re-sealing.

Step 9

Slide the opening pick to cut the adhesive along the left edge of your phone.
If the screen is hard to slice, apply heat to the difficult area for one minute and try again.
Keep in mind that you are now slicing near the screen flex cable and digitizer.

Slide the opening pick to cut the adhesive along the left edge of your phone.

Keep in mind that you are now slicing near the screen flex cable and digitizer.

Step 10

Slide the opening pick around the bottom-left corner and across the bottom of the display to cut the rest of the adhesive.
If the screen is hard to slice, apply heat to the difficult area for one minute and try again.
Keep in mind that you are now slicing near the screen flex cable and digitizer.

Slide the opening pick around the bottom-left corner and across the bottom of the display to cut the rest of the adhesive.

Step 11

Once you have cut around the perimeter of the phone, carefully lift the right edge of the screen, partially opening the phone like a book.
Do not remove the screen yet.
Use an opening pick to carefully cut through any remaining adhesive.

Once you have cut around the perimeter of the phone, carefully lift the right edge of the screen, partially opening the phone like a book.

Do not remove the screen yet.

Use an opening pick to carefully cut through any remaining adhesive.

Step 12

              Flip the screen over

Lift from the top edge and swing the screen over the bottom edge until you can rest it glass-side down.
Be careful not to put any stress on the attached ribbon cable.

Lift from the top edge and swing the screen over the bottom edge until you can rest it glass-side down.

Be careful not to put any stress on the attached ribbon cable.

Step 13

              Disconnect the display

Use your fingernail or a pair of tweezers to carefully peel off the tape covering the screen connector.
If it is in good condition, you can re-use this tape during reassembly. Otherwise, replace it with a piece of Kapton tape.

Use your fingernail or a pair of tweezers to carefully peel off the tape covering the screen connector.

If it is in good condition, you can re-use this tape during reassembly. Otherwise, replace it with a piece of Kapton tape.

Step 14

Insert the tip of a spudger into the opening of the plastic cover securing the screen flex cable.
Pry the plastic cover straight up until it pops out of place.
The plastic cover may spring into the air.
Remove the plastic cover.

Insert the tip of a spudger into the opening of the plastic cover securing the screen flex cable.

Pry the plastic cover straight up until it pops out of place.

The plastic cover may spring into the air.

Remove the plastic cover.

Step 15

Use the tip of a spudger to pry up and disconnect the screen flex cable.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Use the tip of a spudger to pry up and disconnect the screen flex cable.

To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Step 16

              Remove the screen

Remove the screen.
Compare your replacement screen with the original. You may need to transfer additional components (such as the speaker mesh to the new part).
To install the new screen:
Follow this guide if you are using custom-cut adhesives.
If you are using double-sided tape such as Tesa tape, follow this guide.
During the boot-up process after reassembly, the screen will go through a calibration sequence. Do not touch the screen during this process, as it could result in improper touch calibration and create touch issues.

Remove the screen.

Compare your replacement screen with the original. You may need to transfer additional components (such as the speaker mesh to the new part).

To install the new screen:

Follow this guide if you are using custom-cut adhesives.

If you are using double-sided tape such as Tesa tape, follow this guide.

During the boot-up process after reassembly, the screen will go through a calibration sequence. Do not touch the screen during this process, as it could result in improper touch calibration and create touch issues.

Step 17

              Remove the midframe screws

Use a T3 Torx driver to remove the nine 4.4 mm-long screws securing the back cover to the midframe.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Use a T3 Torx driver to remove the nine 4.4 mm-long screws securing the back cover to the midframe.

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Step 18

              Separate the back cover from the midframe

Insert an opening pick into the seam between the midframe and the back cover, right above the SIM card slot.
Slide the opening pick along the right edge of your phone to release the plastic clips securing the back cover to the midframe.

Insert an opening pick into the seam between the midframe and the back cover, right above the SIM card slot.

Slide the opening pick along the right edge of your phone to release the plastic clips securing the back cover to the midframe.

Step 19

Continue sliding the opening pick along the top, left, and bottom edges of your phone until all of the plastic tabs securing the back cover to the midframe are released.

Continue sliding the opening pick along the top, left, and bottom edges of your phone until all of the plastic tabs securing the back cover to the midframe are released.

Step 20

Flip your phone over so the back cover is facing up.
Carefully swing the back cover up to an upright position.
Do not remove the back cover. It is still attached by two ribbon cables.
Rest the back cover against an object such as a cardboard box or soda can.

Flip your phone over so the back cover is facing up.

Carefully swing the back cover up to an upright position.

Do not remove the back cover. It is still attached by two ribbon cables.

Rest the back cover against an object such as a cardboard box or soda can.

Step 21

              Remove the motherboard bracket

Use a T3 Torx screwdriver to remove the seven screws securing the motherboard bracket:
Four 4.0 mm-long screws
Three 2.1 mm-long screws

Use a T3 Torx screwdriver to remove the seven screws securing the motherboard bracket:

Four 4.0 mm-long screws

Three 2.1 mm-long screws

Step 22

Remove the motherboard bracket.

Remove the motherboard bracket.

Step 23

              Disconnect the battery

Use the tip of a spudger to disconnect the battery cable from the motherboard.

Use the tip of a spudger to disconnect the battery cable from the motherboard.

Step 24

              Remove the back cover

Use the tip of a spudger to pry up and disconnect the fingerprint sensor cable.

Use the tip of a spudger to pry up and disconnect the fingerprint sensor cable.

Step 25

Use the tip of a spudger to pry up and disconnect the front sensor array cable.

Use the tip of a spudger to pry up and disconnect the front sensor array cable.

Step 26

Remove the back cover.

Remove the back cover.

Step 27

              Remove the loudspeaker

Use a T3 Torx driver to remove the two 4.2 mm-long screws from the loudspeaker assembly.

Use a T3 Torx driver to remove the two 4.2 mm-long screws from the loudspeaker assembly.

Step 28

Insert the tip of a spudger underneath the loudspeaker assembly.
Be careful not to puncture the white membranes on either side of the loudspeaker if you are intending to reuse it.
Flip the loudspeaker assembly over so it lightly rests on top of the battery.

Insert the tip of a spudger underneath the loudspeaker assembly.

Be careful not to puncture the white membranes on either side of the loudspeaker if you are intending to reuse it.

Flip the loudspeaker assembly over so it lightly rests on top of the battery.

Step 29

Use a pair of tweezers to disconnect the antenna cable from the loudspeaker assembly.
Grab the metal connector of the antenna cable with your tweezers—not the plastic cable.

Use a pair of tweezers to disconnect the antenna cable from the loudspeaker assembly.

Grab the metal connector of the antenna cable with your tweezers—not the plastic cable.

Step 30

Carefully peel the loudspeaker assembly up off the tape underneath it.
Be careful not to puncture the white membranes on either side of the loudspeaker if you are intending to reuse it.
Remove the loudspeaker assembly.

Carefully peel the loudspeaker assembly up off the tape underneath it.

Remove the loudspeaker assembly.

Step 31

              Remove the front-facing camera

Use your fingers or a pair of tweezers to peel the tape off of the copper foil.
The copper foil is thin and easily punctured.

Use your fingers or a pair of tweezers to peel the tape off of the copper foil.

The copper foil is thin and easily punctured.

Step 32

Use the flat end of a spudger to disconnect the front-facing camera from the motherboard.
Remove the front-facing camera.

Use the flat end of a spudger to disconnect the front-facing camera from the motherboard.

Remove the front-facing camera.

Step 33

              De-route the antenna flex cable

Use your fingers or a pair of tweezers to pull the antenna cable out from underneath the tape covering it.

Use your fingers or a pair of tweezers to pull the antenna cable out from underneath the tape covering it.

Step 34

              Disconnect the loudspeaker cable

Use the tip of a spudger to disconnect the loudspeaker cable from the motherboard.

Use the tip of a spudger to disconnect the loudspeaker cable from the motherboard.

Step 35

              Disconnect the headphone jack

Use the tip of a spudger to disconnect the headphone jack cable from the motherboard.

Use the tip of a spudger to disconnect the headphone jack cable from the motherboard.

Step 36

Use a pair of tweezers to remove the tape on the earpiece speaker covering the antenna flex cable.

Use a pair of tweezers to remove the tape on the earpiece speaker covering the antenna flex cable.

Step 37

              Remove the charging port screw

Use a T3 Torx screwdriver to remove the 2.1 mm-long screw securing the charging port.

Use a T3 Torx screwdriver to remove the 2.1 mm-long screw securing the charging port.

Step 38

              Remove the motherboard

The motherboard is secured to the midframe by plastic clips.
Insert the tip of a spudger into the gap between the motherboard and the midframe near the front-facing cameras to pop it free from the first clip.

The motherboard is secured to the midframe by plastic clips.

Insert the tip of a spudger into the gap between the motherboard and the midframe near the front-facing cameras to pop it free from the first clip.

Step 39

Grab the motherboard with your fingers and open it like a book.
This will release the rest of the clips.
Lift the motherboard straight out to remove it.

Grab the motherboard with your fingers and open it like a book.

This will release the rest of the clips.

Lift the motherboard straight out to remove it.

Step 40

              Disconnect the camera assembly

Use the flat end of a spudger to disconnect the left camera from the motherboard.

Use the flat end of a spudger to disconnect the left camera from the motherboard.

Step 41

Use the tip of a spidger to disconnect the right camera from the motherboard.
Use caution not to damage the small capacitors on the motherboard.

Use the tip of a spidger to disconnect the right camera from the motherboard.

Use caution not to damage the small capacitors on the motherboard.

Step 42

              Remove the front-facing camera assembly

Remove the front-facing camera assembly.
If your replacement camera module has a plastic spacer, be sure to remove it before you install the module.
Make sure the lens surface is smudge and dust free before you install the camera assembly.

Remove the front-facing camera assembly.

If your replacement camera module has a plastic spacer, be sure to remove it before you install the module.

Make sure the lens surface is smudge and dust free before you install the camera assembly.

Step 43

              Remove the USB-C port assembly

Remove the USB-C port assembly from the motherboard.
Only the motherboard remains.

Remove the USB-C port assembly from the motherboard.

Only the motherboard remains.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Sam Omiotek

Member since: 02/25/2019

55,294 Reputation

                                      288 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Guide Team                        

                                                  Member of Guide Team 



                    Community                     


                                            10 Members                     


                                            9,216 Guides authored

Jordan Oliver - Jun 7, 2021

Can you even get parts for these?

Ion Sastras - Jul 13, 2021

Unfortunately, I CAN’T FIND WHERE TO BUY THE MOTHERBOARD :(

kenzoeric - Jul 21, 2021

Hello I need a motherboard of pixel 4a is urgent after make a reset I don’t have any application on display only the parameters and calculator and wach

Need a solution

Lucky Chang - Feb 10, 2022

Can anyone tell me what is the SIM Connector part number for Pixel 4a5g?

Introduction#

What you need#

Team#

Introduction

What you need

Team